JL Audio Car Speaker SB F FCSZX 10W3v3 User Manual

®
Stealthbox  
INSTALLATION GUIDE  
for the  
START  
HERE  
SB-F-ZX3/10W3  
(2000-Up ZX3 2-door & 2001-Up ZX5  
4-door hatchback)  
STEP 1: Remove the four Phillips head  
screws, panel button and cargo light from  
driver’s side rear cargo area.  
STEP 2: Remove the plastic safety belt  
retractor cover. Look up under the plastic  
cover for a Phillips head screw. Remove this  
screw. (The location of this screw is shown in  
the picture by the upward arrow).  
STEP 3: Remove the two plastic Phillips head  
screws indicated by the arrows.These are  
located in the driver’s rear hatch plastic trim  
panel. Remove the carpeted side panel.This  
panel will be cut in Step 9 so as to form a  
trim for the Stealthbox.The view shown  
above is from the back seat looking toward  
the hatch.Also remove the hatch flooring (this  
flooring will be re-installed later).  
This Stealthbox is a product that  
requires professional installation skills  
and tools.  
Please read this installation guide  
thoroughly before beginning the  
project. It will guide you step by step  
through the installation. Several of  
the steps in this process may require  
two people to accomplish.  
It is absolutely vital that the  
enclosure be properly mounted to  
the vehicle according to these  
instructions. Failure to mount the  
enclosure properly presents two  
problems: 1)The sub-bass  
performance will suffer due to the  
movement of the enclosure caused  
by the force exerted by the  
woofer(s) and 2) A loose enclosure  
presents a serious safety hazard in  
the event of a collision or sudden  
deceleration.  
®
STEP 4: Locate the MOLEX plug and pull it  
loose from the side panel.  
STEP 5: Remove theT-27TORX head bolt  
from the back side of the driver’s side rear  
wheel well. Remove the Phillips screw from  
directly below theTORX head bolt.  
STEP 6: Loosen the driver’s side rear fabric  
wheel well by pulling it toward the front of  
the car.  
.
Please enjoy your JL Audio  
Stealthbox responsibly.  
Continued on Page 2  
SB-F-ZX3/10W3, JL AUDIO, Inc 2002  
Page 1  
Sheet SKU#011157 Revision 06/18/02  
 
STEP 14: From outside of the car, slide hand  
between the pulled fabric wheel well (Step  
6) and the car’s body. Feel for the threaded  
mounting stud.  
Cont.  
From  
Page 3  
STEP 15: Place fender washer, lock washer  
and 3/8 in. nut onto threaded mounting stud.  
Tighten firmly using a 9/16 in. deep socket.  
STEP 16: After securely mounting the  
Stealthbox, push fabric wheel well back into  
place. ReinstallTORX head bolt and Phillips  
head screw that was removed in Step 5.  
CONGRATULATIONS!  
INSTALL COMPLETE.  
STEP 11: Reinstall the plastic side panel and  
the 4 Phillips head screws, the safety belt  
retractor cover and cargo light removed in  
Steps 1 & 2. Place cut carpet side panel back  
into car.  
STEP 12: Run speaker wire to the location of  
the Stealthbox enclosure.At this time please  
check for proper operation of woofer.  
STEP 17: Replace hatch carpet back into car.You  
will need to tuck the carpet under the Stealthbox.  
STEP 13: Slide Stealthbox enclosure into the  
corner of cargo area. Insert the 3/8 in.  
threaded mounting stud into the enclosure  
and line it up with the 1/2 in. (12.7 mm) hole.  
Slide through to outside of car. Make sure  
®
relocated MOLEX plug and wiring is not  
going to be pinched by enclosure or side  
panels.  
Included Hardware:  
(1) 3/8” Washer  
(1) 3/8” Lock Washer  
(1) 3/8” Hex nut  
(1) 3/8” x 2 1/4” Socket Cup Set Screw  
Mid/High Frequency Driver Information:  
Specifications:  
Enclosure Type: Acoustic Suspension (Sealed)  
Driver Type: One JL AUDIO 10W3-D2 Subwoofer  
Nominal Impedance: 4  
Front Location Driver Size:  
5"x7”  
Cont. Power Handling: 250 Watts  
Applicable JL Audio Products:  
TR570-CXi,  
XR570-CXi or CSi  
JLAudio recommends using a high quality amplifier such as the JLAudio 250/1. The diagram below shows the recommended  
®
crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox .  
XR570-CXi  
Rear Location Driver Size:  
5"x7”  
+12VDC  
Ground Remote  
Preamp Output Section  
Output Mode  
Bass Control  
Infrasonic Filter  
Amp LP Filter  
Mode/Slope  
Amplifier Input Section  
Input Voltage  
Input Sens. Signal Sensing  
Applicable JL Audio Products:  
TR570-CXi,  
Full-Range/Low-Pass/High-Pass  
Off/30Hz  
+7  
Off/12dB/24dB  
Low/High  
Off/On  
+3  
+1  
+10  
+13  
XR570-CXi or CSi  
JL AUDIO 250/1  
monoblock subwoofer amplifier  
TR570-CXi  
Left Ch.  
Right Ch.  
LF Boost (dB) Filter Freq. (Hz)  
Left Ch.  
Right Ch.  
The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information  
about installing and tuning this amplifier.  
10369 N. Commerce Pkwy, Miramar, Florida 33025  
Phone: 954.443.1100  
Fax: 954.443.1111  
SB-F-ZX3/10W3, JL AUDIO, Inc 2002  
Page 3  
Sheet SKU#011157 Revision 06/18/02  
 

Indesit Washer Dryer IS31 User Manual
Infinity Speaker System TSS 450 User Manual
Jet Tools Saw JWBS 18X User Manual
JVC Car Speaker KD DV7405 User Manual
JVC CRT Television HV 28P37SUE User Manual
Kenmore Range 7909662 User Manual
Kenmore Refrigerator 25331115308 User Manual
KitchenAid Oven KEBK171 User Manual
Kodak Camera Accessories 1078419 User Manual
Kompernass Electric Pencil Sharpener KH4450 User Manual