JL Audio Speaker FS110 W5 User Manual

SKU#011292_02_09  
FS110 -W5  
Installation Instructions  
(all models)  
1. Unpack the FS110-W5 and  
The FS110-W5 is designed to be a universal-application Subwoofer  
determine where it will be  
System. The exact mounting procedure employed will vary based  
on the requirements of the installation. The steps outlined in these  
instructions take most considerations into account and should be  
read thoroughly prior to beginning your installation.  
mounted. Consider access to the  
opposite side of the mounting  
surface for securing mounting  
bolts and visual confirmation  
you are not drilling through any  
wires, hoses or even the hull of  
the vessel. In addition, consider  
the structural integrity of the  
mounting surface itself and that  
installation does not interfere with  
water drainage, hatch lids, or any  
moving parts on the vessel.  
4. In addition to the mounting holes,  
one additional hole must be  
marked for the entry of the speaker  
wire into the enclosure. For this  
hole, consider the most clean and  
protected wire run (this may mean  
the top or back of the enclosure).  
2. Using a Phillips-head screwdriver,  
remove the 3 Stainless-Steel screws  
that mount the woofer to the  
5. Drill a pilot hole into the  
enclosure at each of the marks  
made in Step 3. Enlarge each  
pilot hole to the appropriate  
diameter, as dictated by the  
mounting hardware and speaker  
cable used.  
enclosure and remove the woofer.  
3. Mark the enclosure for the  
location of the mounting holes.  
There should be at least 2  
mounting bolts used to secure the  
enclosure (3 or more mounting  
bolts are recommended for extra  
strength and stability). On the  
inside of the enclosure, ensure  
there is ample room around the  
mounting points for the mounting  
hardware (not included).  
6. Once all of the holes are drilled  
through the enclosure, hold it  
in the exact mounting location  
10. Make the terminal connections to  
determined in Step 1. Using the  
the woofer observing the correct  
holes drilled in Step 5 as a guide,  
mark the mounting surface so  
enclosure’s woofer mounting hole.  
that corresponding enclosure  
polarity and set the woofer in the  
Orient the woofer’s logo so it is  
appropriate for the installation  
and so that each of the woofer’s  
mounting holes line up with the  
pre-drilled holes in the enclosure.  
Re-mount the woofer using the  
3 Stainless-Steel screws removed  
in Step 2 and the 3 additional  
Stainless-Steel screws included  
with the enclosure.  
mounting holes can be drilled.  
7. At each mark made in Step 6, drill  
pilot holes and then appropriately-  
sized mounting holes into the  
mounting surface.  
Reccomended Hardware/Mounting  
(Stainless-Steel)  
Hex Head Bolt  
Fender Washer  
Silicone Sealant  
8. Run the wire into the enclosure  
leaving 18" within the enclosure  
so that the woofer can be easily  
wired and mounted. Fill the hole  
through which the wire is run  
with silicone caulk to both seal  
the enclosure and protect the  
wire from abrasion.  
ENCLOSURE WA LL  
MOUNTING SURFACE  
11. You have completed the  
installation of your FS110-W5.  
Enjoy your new Enclosed Marine  
Subwoofer System.  
Fender Washer  
9. Securely mount the enclosure  
using the mounting hardware and  
seal the enclosure at the mounting  
holes with a silicone caulk.  
For questions concerning installation of  
this product, contact JL Audio Technical  
Support during regular business hours at  
(954) 443-1100.  
Lock Washer  
Hex Nut  
 

Insignia Flat Panel Television NS 40L240A13 User Manual
IPSO Automobile IHC012 User Manual
JVC Car Video System 0305MNMMDWJEIN User Manual
Karcher Carpet Cleaner K 2110 M User Manual
Kenwood Car Speaker KFC S200 User Manual
KitchenAid Ice Maker KUIC18NNTS1 User Manual
KitchenAid Indoor Furnishings Sinks 8534966 User Manual
KitchenAid Refrigerator KURS24LS User Manual
KitchenAid Ventilation Hood KWCU205H User Manual
Klipsch Speaker SW 308 User Manual