JL Audio C3 525 User Manual

owner’s manual  
5.25-inch (130 mm) Convertible 2-Way Component System  
Thank you for choosing a JL Audio Evolution™ C3 Convertible  
Component System for your automotive sound system.  
These Evolution™ Speakers have been designed and manufactured to  
exacting standards in order to ensure years of musical enjoyment in your  
vehicle. For maximum performance and extended warranty  
coverage, we highly recommend that you have your new speakers installed  
by an authorized JL Audio dealer. Your authorized  
dealer has the training, expertise and installation equipment to ensure  
optimum performance from this product. Should you  
decide to install the speakers yourself, please take the time  
to read this manual thoroughly so as to familiarize yourself  
with its installation requirements and setup procedures.  
If you have any questions regarding the instructions in this  
manual or any aspect of your amplifier’s operation, please contact your  
authorized JL Audio dealer for assistance. If you need further assistance,  
please call the JL Audio Technical Support Department  
at (954) 443-1100 during business hours.  
C3-525 sPeCIFICaTIons  
Woofers: Injection-Molded Polymer Frame, Patented Elevated  
Frame Cooling (U.S. Patent #6,219,431 & #6,229,902), DMA-  
Optimized Motor System, Mineral-Filled Polypropylene Cone,  
Rubber Surround, 1-in. / 25 mm Voice Coil, Kapton® Former,  
Low-Profile, Symmetrical Roll Spider, Ferrite Magnet  
Included Components and Parts:  
• Two C3-525cw 5.25-inch (130 mm) Woofers  
• Two C3-100ct 1.00-inch (25 mm) Tweeters  
• Two C3-525-XO Crossover Networks  
• Two Surface-Mount Tweeter Fixtures  
• Two Coaxial-Mount Tweeter Fixtures  
Tweeters: 1.00 in. / 25 mm Silk Soft Dome with Ferrofluid  
Cooling and Damping and Neodymium Magnet  
Fixed Angle Flush-Mount, Surface-Mount and Coaxial-Mount  
Systems  
• Two Flush-Mount Tweeter Fixtures  
• Two Metal Spring Clips for Tweeter Fixtures  
• Two Metal Mesh Woofer Grilles with ABS Grille Trays  
• Twelve #8 x 1.25 inch (32 mm) Sheet Metal Screws  
• Four #6 x 1.00-inch (25 mm) Sheet Metal Screws  
• Two 1.00-inch (25 mm) Machine Screws  
• Eight Mounting Clips for Woofer Mounting  
• Two 6.4 mm Female Crimpable Connectors  
• Two 4.7 mm Male Crimpable Connectors  
• Two 4.7 mm Female Crimpable Connectors  
• Four 2.8 mm Female Crimpable Connectors  
• Two 2.8 mm Male Crimpable Connectors  
• Twelve Crimpable Spade Connectors  
Crossover Networks: 2-way networks with 1st order  
low-pass and 2nd order high-pass filters, premium Mylar®  
capacitors, air-core inductors, 4-position adjustable tweeter  
output level, 3-position midrange presence control,  
Polyswitch tweeter protection  
Continuous Power Handling: 75 Watts (RMS Method)  
Frequency Response: 48 Hz - 25 KHz ( 3 dB)  
Efficiency @ 1W/1m: 90.0 dB @ 1W/1m  
Nominal Impedance: 4 ohms  
• One Woofer Mounting Template  
Due to ongoing product development, all specifications are subject to change without notice.  
3
GeTTInG sTarTeD  
aDJusTaBle mIDranGe PresenCe  
•ꢀTurnꢀoffꢀtheꢀaudioꢀsystem.ꢀItꢀisꢀalsoꢀ  
advisableꢀtoꢀdisconnectꢀtheꢀnegativeꢀ(–)ꢀ  
terminalꢀofꢀyourꢀvehicle’sꢀbatteryꢀwheneverꢀ  
performingꢀinstallationꢀwork.  
•ꢀBeforeꢀcutting,ꢀdrillingꢀorꢀinsertingꢀanyꢀscrew,ꢀ  
checkꢀclearancesꢀonꢀbothꢀsidesꢀofꢀtheꢀplannedꢀ  
mountingꢀsurface.ꢀAlsoꢀcheckꢀforꢀanyꢀpotentialꢀ  
obstacles,ꢀsuchꢀasꢀwindowꢀtracksꢀandꢀmotors,ꢀ  
wiringꢀharnesses,ꢀetc.ꢀCheckꢀbothꢀsidesꢀofꢀtheꢀ  
YourꢀC3ꢀcrossoverꢀnetworksꢀprovideꢀaꢀuniqueꢀ  
midrangeꢀpresenceꢀcontrol,ꢀlocatedꢀunderꢀtheꢀcover.ꢀ  
Theꢀmidrangeꢀpresenceꢀisꢀselectableꢀviaꢀaꢀsetꢀofꢀpinsꢀ  
andꢀallowsꢀforꢀthreeꢀsettings.ꢀTheseꢀsettingsꢀaffectꢀtheꢀ  
amplitudeꢀofꢀtheꢀupperꢀmidrangeꢀresponseꢀofꢀtheꢀC3ꢀ  
componentꢀwoofer.ꢀWeꢀrecommendꢀthatꢀyouꢀbeginꢀ  
yourꢀlisteningꢀinꢀtheꢀ“REF”ꢀ(Reference)ꢀandꢀadjustꢀ  
upꢀorꢀdownꢀasꢀneededꢀtoꢀcompensateꢀforꢀmountingꢀ  
location,ꢀorientationꢀorꢀpersonalꢀtaste.  
vehicle,ꢀmanyꢀvehiclesꢀareꢀnotꢀsymmetrical!  
•ꢀAlwaysꢀwearꢀprotectiveꢀeyewear.  
CrossoVer neTworK InsTallaTIon  
TheꢀcrossoverꢀnetworksꢀsuppliedꢀwithꢀyourꢀC3ꢀ  
Systemꢀshouldꢀbeꢀinstalledꢀinꢀaꢀdryꢀlocationꢀinsideꢀ  
yourꢀvehicle.ꢀDOꢀNOTꢀINSTALLꢀTHEMꢀINSIDEꢀOFꢀ  
AꢀDOOR!ꢀDoorsꢀoftenꢀgetꢀwetꢀonꢀtheꢀinside,ꢀwhichꢀ  
canꢀdamageꢀyourꢀcrossoverꢀnetworksꢀandꢀcouldꢀ  
potentiallyꢀdamageꢀyourꢀentireꢀsoundꢀsystem.ꢀTheꢀ  
crossoversꢀcanꢀbeꢀscrewedꢀintoꢀaꢀsolidꢀsurfaceꢀviaꢀtwoꢀ  
holesꢀlocatedꢀunderꢀtheꢀprotectiveꢀcoverꢀofꢀtheꢀcase.ꢀ  
Toꢀaccessꢀtheseꢀholes,ꢀsimplyꢀsqueezeꢀtheꢀsidesꢀofꢀtheꢀ  
coverꢀwhileꢀgentlyꢀpullingꢀtheꢀcoverꢀawayꢀfromꢀtheꢀ  
base.ꢀMakeꢀsureꢀthatꢀyourꢀmountingꢀlocationꢀwillꢀnotꢀ  
causeꢀdamageꢀtoꢀwiring,ꢀfuelꢀlines,ꢀbrakeꢀlinesꢀorꢀanyꢀ  
otherꢀvitalꢀcomponentꢀofꢀyourꢀvehicle.ꢀOnceꢀyouꢀhaveꢀ  
screwedꢀtheꢀcaseꢀinꢀandꢀmadeꢀyourꢀconnections,ꢀsnapꢀ  
theꢀprotectiveꢀcoverꢀbackꢀintoꢀplace.ꢀ  
aDJusTaBle TweeTer leVel  
C3ꢀcrossoverꢀnetworksꢀalsoꢀprovideꢀfourꢀlevelsꢀ  
ofꢀtweeterꢀadjustabilityꢀdesignedꢀtoꢀcompensateꢀforꢀ  
differentꢀmountingꢀlocations,ꢀvehicleꢀinteriorsꢀandꢀ  
personalꢀtaste.ꢀTheseꢀlevelsꢀareꢀselectableꢀviaꢀaꢀsetꢀofꢀ  
pinsꢀlocatedꢀunderꢀtheꢀclearꢀcoverꢀofꢀeachꢀcrossoverꢀ  
case.ꢀWeꢀrecommendꢀthatꢀyouꢀbeginꢀlisteningꢀinꢀtheꢀ  
“REF”ꢀ(Reference)ꢀposition.ꢀToꢀfindꢀtheꢀoptimumꢀ  
tonalꢀbalanceꢀinꢀyourꢀinstallation,ꢀexperimentꢀwithꢀ  
alternateꢀtweeterꢀlevelꢀsettingsꢀbyꢀmovingꢀtheꢀpins.ꢀItꢀ  
isꢀsafeꢀtoꢀswitchꢀjumpersꢀwhileꢀtheꢀsystemꢀisꢀplaying.  
TweeTer ProTeCTIon  
TheꢀC3ꢀcrossoverꢀnetworksꢀareꢀequippedꢀwithꢀ  
anꢀadvancedꢀelectronicꢀtweeterꢀprotectionꢀcircuitꢀ  
designedꢀtoꢀminimizeꢀtheꢀpossibilityꢀofꢀtweeterꢀ  
failure.ꢀThisꢀelectronicꢀdeviceꢀmonitorsꢀcurrentꢀgoingꢀ  
toꢀtheꢀtweeterꢀandꢀwillꢀdisconnectꢀtheꢀtweeterꢀfromꢀ  
theꢀsignalꢀwhenꢀitꢀsensesꢀoverload.ꢀShouldꢀthisꢀoccurꢀ  
whileꢀlisteningꢀtoꢀtheꢀaudioꢀsystem,ꢀsimplyꢀreduceꢀtheꢀ  
volumeꢀforꢀaꢀfewꢀsecondsꢀandꢀtheꢀprotectionꢀcircuitꢀ  
willꢀresetꢀitselfꢀautomatically.  
CrossoVer neTworK aDJusTmenT  
Theꢀcrossoverꢀnetworksꢀhaveꢀbeenꢀdesignedꢀtoꢀ  
allowꢀtonalꢀadjustmentsꢀtoꢀtheꢀupperꢀmidrangeꢀ  
responseꢀandꢀtweeterꢀlevel.ꢀTheseꢀadjustmentsꢀmakeꢀ  
itꢀpossibleꢀtoꢀfine-tuneꢀyourꢀsystemꢀtoꢀsuitꢀyourꢀ  
listeningꢀpreferencesꢀandꢀtoꢀcompensateꢀforꢀvariousꢀ  
speakerꢀmountingꢀapplications.ꢀ  
4 | JL Audio - C3-525 Owner’s Manual  
wIrInG Your sPeaKer sYsTem  
C3ꢀConvertibleꢀComponentsꢀgiveꢀyouꢀtheꢀoptionꢀ  
ofꢀinstallingꢀtheꢀspeakersꢀasꢀseparateꢀcomponentꢀ  
speakerꢀsystemsꢀorꢀasꢀcoaxialꢀsystemsꢀ(tweetersꢀ  
mountedꢀontoꢀtheꢀcenterꢀofꢀeachꢀwoofer).  
Positiveꢀ(+)ꢀandꢀnegativeꢀ(–)ꢀconnectionsꢀtoꢀtheꢀ  
crossoverꢀfromꢀtheꢀamplifierꢀoutputsꢀareꢀmadeꢀwithꢀ  
theꢀterminalsꢀlabeledꢀ“IN+”ꢀandꢀ“IN–”.ꢀTheꢀPositiveꢀ  
andꢀNegativeꢀoutputsꢀtoꢀtheꢀwooferꢀconnectionsꢀareꢀ  
labeledꢀ“W+”ꢀandꢀ“W–”onꢀtheꢀCrossoverꢀandꢀshouldꢀ  
beꢀconnectedꢀtoꢀcorrespondingꢀ“WFR+”ꢀandꢀꢀ  
WFR–”ꢀterminalsꢀonꢀtheꢀwooferꢀ(asꢀillustratedꢀ  
below).ꢀTheꢀtweeterꢀconnectionsꢀvaryꢀbyꢀsystemꢀ  
configurationꢀandꢀmayꢀbeꢀmadeꢀinꢀoneꢀofꢀtwoꢀways.ꢀ  
Inꢀcomponentꢀconfiguration,ꢀtheꢀtweeterꢀoutputs,ꢀ  
labeledꢀ“T+”ꢀandꢀ“T”ꢀonꢀtheꢀCrossoverꢀshouldꢀbeꢀwiredꢀ  
directlyꢀtoꢀtheꢀcorrespondingꢀleadꢀonꢀtheꢀtweeterꢀ(Seeꢀ  
DiagramꢀA).ꢀInꢀcoaxialꢀconfiguration,ꢀtheꢀtweeterꢀisꢀ  
connectedꢀviaꢀanꢀinternalꢀjumperꢀ(Seeꢀpageꢀ6ꢀforꢀmoreꢀ  
information)ꢀandꢀtheꢀCrossoverꢀtweeterꢀoutputsꢀshouldꢀ  
beꢀwiredꢀtoꢀtheꢀcorrespondingꢀ“TWT+”ꢀandꢀ“TWT”ꢀ  
terminalsꢀonꢀtheꢀwooferꢀ(SeeꢀDiagramꢀB).ꢀ  
WARNING  
!!  
It is absolutely vital that your component system  
is connected as shown in this manual. Failure to  
connect the system as shown may result in damage to  
your speakers which is NOT covered under warranty.  
DIaGram a: Component system wiring  
Do not substitute different crossover networks into  
your C3 System. Do not use crossover networks  
intended for different C3 models.  
Amplifier  
Output  
Red  
Black  
DIaGram B: Coaxial system wiring  
Amplifier  
Output  
Red  
Black  
5
ConVerTIBle ComPonenTs  
C3ꢀConvertibleꢀComponentsꢀgiveꢀyouꢀtheꢀoptionꢀ  
ofꢀinstallingꢀtheꢀspeakersꢀasꢀseparateꢀcomponentꢀ  
speakerꢀsystemsꢀorꢀasꢀcoaxialꢀsystemsꢀ(tweetersꢀ  
mountedꢀontoꢀtheꢀcenterꢀofꢀeachꢀwoofer).  
Coaxial system set-up  
TheꢀCoaxialꢀconfigurationꢀofꢀtheꢀC3-525ꢀisꢀ  
achievedꢀbyꢀinstallingꢀaꢀtweeterꢀontoꢀtheꢀcenterꢀofꢀ  
eachꢀwooferꢀusingꢀtheꢀsuppliedꢀcoaxialꢀtweeterꢀposts.  
First,ꢀremoveꢀtheꢀphaseꢀplugsꢀfromꢀtheꢀwoofersꢀ(ifꢀ  
present)ꢀbyꢀpushingꢀdownꢀfirmly/evenlyꢀonꢀtheꢀplugꢀ  
withꢀthumbꢀandꢀindexꢀfingerꢀandꢀturningꢀ1/4ꢀturnꢀ  
counter-clockwiseꢀtoꢀunlockꢀandꢀremove.ꢀTheꢀphaseꢀ  
plugsꢀwillꢀnotꢀbeꢀusedꢀinꢀcoaxialꢀconfigurationꢀandꢀ  
shouldꢀbeꢀsetꢀasideꢀforꢀpossibleꢀfutureꢀuse.  
Note: If the C3 system is to be used in a coaxial  
configuration, the phase plugs must be removed to  
accept the tweeter and tweeter post.  
Component system set-up  
TheꢀComponentꢀconfigurationꢀofꢀtheꢀC3-525ꢀ  
isꢀachievedꢀbyꢀwiringꢀtheꢀtweeterꢀtoꢀtheꢀcrossoverꢀ  
separatelyꢀandꢀinstallingꢀtheꢀincludedꢀphaseꢀplugsꢀ  
ontoꢀtheꢀcenterꢀofꢀeachꢀwoofer.ꢀThe woofers are  
factory-packaged in the component system  
configuration with phase plugs installed.  
Theꢀphaseꢀplugsꢀattachꢀtoꢀtheꢀwoofersꢀusingꢀaꢀ  
simpleꢀbayonetꢀ(twistꢀandꢀlock)ꢀmechanism.ꢀ  
Toꢀremoveꢀtheꢀphaseꢀplugs,ꢀsimplyꢀapplyꢀ  
downwardꢀpressureꢀwithꢀyourꢀthumbꢀandꢀindexꢀ  
fingerꢀandꢀtwistꢀ1/4ꢀturnꢀcounteclockwiseꢀuntilꢀ  
released.ꢀThenꢀpullꢀtheꢀphaseꢀplugꢀoffꢀtheꢀreceiver.  
Toꢀreattachꢀtheꢀphaseꢀplugs,ꢀalignꢀtheꢀtwoꢀ  
tabsꢀonꢀtheꢀinsideꢀofꢀeachꢀphaseꢀplugꢀwithꢀtheꢀ  
groovesꢀonꢀtheꢀouterꢀdiameterꢀofꢀtheꢀreceiverꢀ  
inꢀtheꢀcenterꢀofꢀtheꢀwoofer.ꢀWithꢀtheseꢀaligned,ꢀ  
slideꢀtheꢀphaseꢀplugꢀdownꢀintoꢀplaceꢀuntilꢀitꢀ  
stops,ꢀapplyingꢀgentleꢀpressure.ꢀToꢀlock,ꢀpushꢀ  
downꢀfirmly/evenlyꢀonꢀtheꢀplugꢀwithꢀthumbꢀandꢀ  
indexꢀfingerꢀandꢀturnꢀ1/4ꢀturnꢀclockwise.ꢀ  
Forꢀwooferꢀmountingꢀinstructions,ꢀpleaseꢀreferꢀ  
toꢀPageꢀ8ꢀofꢀthisꢀManual.ꢀForꢀseparateꢀtweeterꢀ  
mountingꢀinstructions,ꢀpleaseꢀreferꢀtoꢀPagesꢀ12-13ꢀofꢀ  
thisꢀManual.  
Next,ꢀrouteꢀtheꢀtweeter’sꢀPositiveꢀ(+)ꢀandꢀꢀ  
Negativeꢀ(-)ꢀwireꢀleadsꢀthroughꢀtheꢀcenterꢀofꢀtheꢀ  
coaxialꢀtweeterꢀpostꢀfromꢀtheꢀlargeꢀtweeter-cupꢀendꢀ  
andꢀoutꢀtheꢀsmallerꢀendꢀ(SeeꢀFigureꢀA).ꢀTheꢀtweeterꢀ  
mountsꢀtoꢀtheꢀcoaxialꢀtweeterꢀpostꢀusingꢀaꢀsimpleꢀ  
bayonetꢀ(twistꢀandꢀlock)ꢀmechanism.ꢀToꢀattachꢀtheꢀ  
tweeterꢀtoꢀtheꢀpost,ꢀobserveꢀtheꢀindentedꢀlockingꢀ  
slotsꢀonꢀtheꢀouterꢀedgeꢀofꢀtheꢀtweeterꢀbodyꢀandꢀalignꢀ  
theseꢀwithꢀtheꢀtabsꢀvisibleꢀonꢀtheꢀinsideꢀwallsꢀofꢀtheꢀ  
tweeterꢀcupꢀportionꢀofꢀtheꢀtweeterꢀpost.ꢀTheꢀtweeterꢀ  
shouldꢀslideꢀintoꢀplaceꢀeasilyꢀandꢀcanꢀthenꢀbeꢀlockedꢀ  
byꢀpushingꢀdownꢀonꢀtheꢀtweeterꢀandꢀgivingꢀitꢀaꢀsmallꢀ  
clockwiseꢀturnꢀ(SeeꢀFigureꢀB).ꢀ  
Withꢀtheꢀtweeterꢀinstalledꢀintoꢀtheꢀtweeterꢀpost,ꢀ  
connectꢀtheꢀPositiveꢀ(+)ꢀredꢀwireꢀleadꢀonꢀtheꢀtweeterꢀ  
toꢀtheꢀlargerꢀmaleꢀconnectionꢀtabꢀinꢀtheꢀwoofer’sꢀ  
center,ꢀfollowedꢀinꢀtheꢀsameꢀmanner,ꢀbyꢀtheꢀꢀ  
Negativeꢀ(-)ꢀblackꢀleadꢀtoꢀtheꢀsmallerꢀconnectionꢀtab.ꢀ  
(SeeꢀFigureꢀC).  
Now,ꢀnoteꢀtheꢀtwoꢀtabsꢀonꢀtheꢀinsideꢀofꢀtheꢀbottomꢀ  
endꢀofꢀtheꢀtweeterꢀpost.ꢀAlignꢀtheseꢀtabsꢀtoꢀtheꢀ  
channelsꢀvisibleꢀonꢀoppositeꢀsidesꢀofꢀtheꢀreceiverꢀinꢀ  
theꢀwoofer’sꢀcenter.ꢀWhileꢀtuckingꢀtheꢀwiresꢀintoꢀtheꢀ  
tweeterꢀpost,ꢀslideꢀtheꢀtweeterꢀpostꢀdownꢀintoꢀplaceꢀ  
untilꢀitꢀstopsꢀandꢀisꢀreadyꢀtoꢀbeꢀlocked.ꢀToꢀlock,ꢀpushꢀ  
downꢀfirmly/evenlyꢀonꢀtheꢀtweeterꢀpostꢀwithꢀthumbꢀ  
andꢀindexꢀfingerꢀandꢀturnꢀ1/4ꢀturnꢀclockwise.ꢀꢀ  
(SeeꢀFigureꢀD).  
Forꢀwooferꢀmountingꢀinstructions,ꢀpleaseꢀreferꢀtoꢀ  
Pageꢀ11ꢀofꢀthisꢀManual.ꢀ  
6 | JL Audio - C3-525 Owner’s Manual  
DIaGram C: Tweeter Post / Coaxial system Configuration  
FigureꢀA.  
FigureꢀB.  
FigureꢀC.  
FigureꢀD.  
DIaGram D: Phase Plug / Component system Configuration  
7
CoaXIal PlaCemenT ConsIDeraTIons  
Inꢀmostꢀcases,ꢀspeakersꢀinꢀtheꢀcoaxialꢀ  
ComPonenT PlaCemenT ConsIDeraTIons  
Aꢀcomponentꢀsystemꢀconfigurationꢀgivesꢀyouꢀtheꢀ  
abilityꢀtoꢀplaceꢀtheꢀwooferꢀandꢀtweeterꢀseparatelyꢀ  
inꢀyourꢀvehicleꢀinterior.ꢀThisꢀcanꢀbeꢀgoodꢀorꢀbad,ꢀ  
dependingꢀonꢀhowꢀit’sꢀdone.ꢀAsꢀaꢀgeneralꢀrule,ꢀtheꢀ  
tweetersꢀshouldꢀbeꢀplacedꢀrelativelyꢀcloseꢀtoꢀtheꢀ  
woofersꢀforꢀbestꢀtonalꢀbalanceꢀandꢀmostꢀcoherentꢀ  
imagingꢀ(theꢀcloser,ꢀtheꢀbetter).ꢀAnyꢀseparationꢀ  
greaterꢀthanꢀ8ꢀinchesꢀ(20ꢀcm)ꢀisꢀlikelyꢀtoꢀresultꢀinꢀ  
degradedꢀsoundꢀqualityꢀ(SeeꢀDiagramꢀH).ꢀ  
configurationꢀwillꢀbeꢀplacedꢀintoꢀfactoryꢀspeakerꢀ  
locations.ꢀIfꢀyouꢀhaveꢀsomeꢀspeakerꢀmountingꢀ  
flexibility,ꢀkeepꢀtheꢀfollowingꢀinꢀmind:ꢀLowerꢀ  
mountingꢀlocations,ꢀsuchꢀasꢀtheꢀlowerꢀfrontꢀcornerꢀ  
(SeeꢀDiagramꢀF)ꢀofꢀaꢀdoorꢀorꢀaꢀkick-panelꢀprovideꢀ  
theꢀgreatestꢀpathꢀlengthꢀdistancesꢀforꢀtheꢀsoundꢀ  
emittedꢀbyꢀtheꢀspeakers.ꢀForꢀthisꢀreason,ꢀtheyꢀareꢀ  
generallyꢀmoreꢀdesirableꢀthanꢀhigherꢀmountingꢀ  
locations.ꢀHigherꢀmountingꢀlocationsꢀwillꢀusuallyꢀ  
resultꢀinꢀextremeꢀnear-sideꢀsoundstageꢀbiasꢀwhichꢀ  
compromisesꢀtheꢀstereoꢀlisteningꢀexperienceꢀꢀ  
(SeeꢀDiagramꢀE).ꢀ  
DIaGram e: CoaXIal ConFIGuraTIon - less Desirable Door speaker Placement  
DIaGram F: CoaXIal ConFIGuraTIon - more Desirable Door speaker Placement  
8 | JL Audio - C3-525 Owner’s Manual  
Avoidꢀplacingꢀtweetersꢀwhereꢀtheyꢀwillꢀbeꢀblockedꢀ  
byꢀobjectsꢀinꢀtheꢀinteriorꢀofꢀtheꢀcarꢀ(includingꢀseatedꢀ  
occupants).ꢀWhenꢀselectingꢀaꢀmountingꢀlocation,ꢀ  
lookꢀatꢀbothꢀsidesꢀofꢀtheꢀcarꢀtoꢀmakeꢀsureꢀthatꢀthisꢀ  
locationꢀisꢀclearꢀonꢀbothꢀsides.ꢀ  
Woofersꢀwillꢀusuallyꢀbeꢀplacedꢀintoꢀfactoryꢀ  
speakerꢀlocations.ꢀIfꢀyouꢀhaveꢀsomeꢀwooferꢀmountingꢀ  
flexibility,ꢀkeepꢀtheꢀfollowingꢀinꢀmind:ꢀLowerꢀ  
mountingꢀlocations,ꢀsuchꢀasꢀtheꢀlowerꢀfrontꢀcornerꢀofꢀ  
aꢀdoorꢀ(SeeꢀDiagramꢀH)ꢀorꢀaꢀkick-panelꢀprovideꢀtheꢀ  
greatestꢀpathꢀlengthꢀdistancesꢀforꢀtheꢀsoundꢀemittedꢀ  
byꢀtheꢀwoofer.ꢀForꢀthisꢀreason,ꢀtheyꢀareꢀgenerallyꢀ  
moreꢀdesirableꢀthanꢀhigherꢀmountingꢀlocations.ꢀ  
Higherꢀmountingꢀlocationsꢀoftenꢀresultꢀinꢀextremeꢀ  
near-sideꢀsoundstageꢀbiasꢀwhichꢀcompromisesꢀtheꢀ  
stereoꢀlisteningꢀexperienceꢀꢀ  
Youꢀcanꢀalwaysꢀexperimentꢀwithꢀtweeterꢀ  
placementꢀbeforeꢀcommittingꢀtoꢀaꢀfinalꢀmountingꢀ  
location.ꢀSimplyꢀconnectꢀtheꢀrestꢀofꢀtheꢀsystemꢀandꢀ  
allowꢀplentyꢀofꢀwireꢀlengthꢀforꢀtheꢀtweeters.ꢀUsingꢀ  
Velcro®ꢀorꢀsimilarꢀmaterial,ꢀattachꢀtheꢀtweetersꢀinꢀ  
differentꢀlocationsꢀuntilꢀyouꢀfindꢀtheꢀoneꢀwhereꢀtheyꢀ  
performꢀbest.  
(SeeꢀDiagramꢀG).ꢀ  
DIaGram G: ComPonenT ConFIGuraTIon - less Desirable Door speaker Placement  
DIaGram H: ComPonenT ConFIGuraTIon - more Desirable Door speaker Placement  
9
WARNING  
!!  
Double check the clearance for both speakers  
before proceeding. Many cars are different from  
one side to the other!  
Custom location:ꢀRunꢀspeakerꢀwireꢀtoꢀtheꢀdesiredꢀ  
mountingꢀlocations.ꢀIfꢀyouꢀareꢀrunningꢀwiresꢀintoꢀ  
aꢀdoor,ꢀuseꢀexistingꢀfactoryꢀwiringꢀbootsꢀwheneverꢀ  
possible.ꢀIfꢀyouꢀareꢀdrillingꢀnewꢀholes,ꢀfileꢀtheirꢀedgesꢀ  
andꢀinstallꢀrubberꢀgrommetsꢀintoꢀeachꢀhole.ꢀWiresꢀ  
shouldꢀthenꢀbeꢀcoveredꢀwithꢀaꢀprotective,ꢀflexibleꢀ  
PVCꢀsleeveꢀandꢀthenꢀrunꢀthroughꢀtheꢀdoorꢀjamb.ꢀ  
Makeꢀsureꢀthatꢀtheꢀwiresꢀwillꢀclearꢀdoorꢀhingesꢀandꢀ  
otherꢀstructuresꢀinꢀtheꢀdoor.ꢀIfꢀyouꢀareꢀunsureꢀaboutꢀ  
anyꢀpartꢀofꢀthisꢀprocess,ꢀpleaseꢀcontactꢀyourꢀJLꢀAudioꢀ  
dealerꢀforꢀinstallationꢀhelp.  
Selectꢀanꢀevenꢀsurface.ꢀTighteningꢀaꢀspeakerꢀontoꢀ  
anꢀunevenꢀsurfaceꢀcanꢀdamageꢀit.ꢀCarefullyꢀmeasureꢀ  
andꢀmarkꢀtheꢀ“mountingꢀholeꢀdiameter”ꢀoutlineꢀinꢀ  
theꢀselectedꢀlocationꢀusingꢀtheꢀdimensionsꢀlistedꢀonꢀ  
pageꢀ2.ꢀBeforeꢀdrillingꢀorꢀcuttingꢀonꢀyourꢀinteriorꢀ  
panels,ꢀuseꢀaꢀutilityꢀknifeꢀtoꢀcutꢀanyꢀfabric,ꢀvinylꢀ  
orꢀleatherꢀfromꢀholeꢀlocations.ꢀTheseꢀmaterialsꢀcanꢀ  
easilyꢀbeꢀsnaggedꢀbyꢀaꢀdrillꢀorꢀaꢀsaw,ꢀcausingꢀdamageꢀ  
toꢀtheꢀpanelꢀandꢀpossibleꢀbodilyꢀinjury.ꢀDrillꢀaꢀpilotꢀ  
holeꢀinꢀtheꢀcenterꢀofꢀtheꢀproposedꢀspeakerꢀmountingꢀ  
hole.ꢀThen,ꢀusingꢀaꢀsaberꢀsawꢀwithꢀanꢀappropriateꢀ  
blade,ꢀmakeꢀtheꢀcircularꢀcutꢀoutꢀforꢀtheꢀspeaker.ꢀFileꢀ  
anyꢀroughꢀedges.  
wooFer InsTallaTIon  
Theꢀwoofersꢀshouldꢀbeꢀinstalledꢀinꢀoneꢀofꢀtheꢀ  
followingꢀwaysꢀdependingꢀonꢀlocation:  
Factory location:ꢀIfꢀyouꢀwillꢀbeꢀusingꢀtheꢀfactoryꢀ  
speakerꢀwires,ꢀitꢀmayꢀbeꢀnecessaryꢀtoꢀchangeꢀtheꢀ  
terminations.ꢀThisꢀmayꢀbeꢀaccomplishedꢀbyꢀusingꢀ  
anꢀadaptorꢀplugꢀorꢀsimplyꢀbyꢀcuttingꢀtheꢀfactoryꢀ  
connectorꢀoffꢀandꢀusingꢀtheꢀsuppliedꢀcrimpꢀ  
connectorsꢀtoꢀterminateꢀtheꢀspeakerꢀwires.ꢀTheꢀ  
largeꢀconnectorꢀisꢀforꢀtheꢀpositiveꢀ( )ꢀterminalꢀandꢀ  
+
theꢀsmallꢀconnectorꢀisꢀforꢀtheꢀnegativeꢀ(–)ꢀterminalꢀ  
ofꢀeachꢀwoofer.ꢀKeepꢀinꢀmindꢀthatꢀtheꢀwooferꢀwiresꢀ  
mustꢀbeꢀconnectedꢀtoꢀtheꢀwooferꢀoutputsꢀofꢀtheꢀ  
crossoversꢀsuppliedꢀwithꢀyourꢀsystemꢀasꢀshownꢀinꢀtheꢀ  
diagramꢀonꢀpageꢀ5.ꢀIfꢀyouꢀpreferꢀtoꢀrunꢀnewꢀwires,ꢀ  
referꢀtoꢀtheꢀ“CustomꢀLocation”ꢀinstallationꢀsectionꢀ  
forꢀdetails.ꢀWhicheverꢀmethodꢀyouꢀchoose,ꢀobserveꢀ  
correctꢀpolarityꢀinꢀyourꢀconnections.ꢀIfꢀyouꢀareꢀ  
unsureꢀaboutꢀanyꢀofꢀtheseꢀissues,ꢀcontactꢀyourꢀꢀ  
JLꢀAudioꢀdealerꢀforꢀinstallationꢀassistance.  
Afterꢀcuttingꢀtheꢀhole,ꢀcheckꢀtoꢀseeꢀthatꢀtheꢀ  
Yourꢀnewꢀspeakersꢀhaveꢀbeenꢀdesignedꢀtoꢀinstall,ꢀ  
withoutꢀmodifications,ꢀintoꢀmostꢀvehiclesꢀthatꢀacceptꢀ  
aꢀ6.5-inchꢀ(160ꢀmm)ꢀspeaker.ꢀMostꢀfactoryꢀ6.5-inchꢀ  
speakersꢀuseꢀfourꢀmountingꢀscrewsꢀwhichꢀwillꢀlineꢀupꢀ  
withꢀtheꢀmountingꢀholesꢀonꢀyourꢀwoofers.ꢀ  
speakerꢀframeꢀfitsꢀintoꢀitsꢀmountingꢀholeꢀcleanly.ꢀ  
Doꢀnotꢀforceꢀtheꢀframeꢀintoꢀaꢀholeꢀthatꢀisꢀtooꢀsmall.ꢀ  
Onceꢀtheꢀspeakerꢀisꢀinꢀplace,ꢀuseꢀtheꢀholesꢀonꢀtheꢀ  
speaker’sꢀmountingꢀflangeꢀtoꢀmarkꢀtheꢀpanelꢀwhereꢀ  
theꢀfourꢀmountingꢀscrewsꢀwillꢀbeꢀpositionedꢀ(Seeꢀ  
DiagramꢀJ).ꢀRemoveꢀtheꢀspeakerꢀandꢀdrillꢀ1/8-inchꢀ  
(3ꢀmm)ꢀholesꢀatꢀeachꢀmark.ꢀInsertꢀtheꢀmountingꢀ  
clipsꢀwithꢀtheꢀflatꢀsideꢀtowardsꢀtheꢀspeaker.ꢀConnectꢀ  
theꢀspeakerꢀwires,ꢀobservingꢀcorrectꢀpolarity,ꢀandꢀ  
secureꢀtheꢀspeakerꢀandꢀgrilleꢀtrayꢀtoꢀtheꢀpanelꢀbyꢀ  
evenlyꢀtighteningꢀbyꢀhandꢀtheꢀprovidedꢀ#8ꢀxꢀ1.25ꢀ  
inchꢀ(32ꢀmm)ꢀmountingꢀscrews.ꢀMakeꢀsureꢀtheꢀ  
wooferꢀisꢀsecuredꢀsoꢀthatꢀairꢀdoesꢀnotꢀleakꢀaroundꢀ  
theꢀmountingꢀflange.ꢀAirꢀleaksꢀwillꢀcauseꢀaꢀsevereꢀ  
degradationꢀinꢀsoundꢀquality.ꢀSealꢀanyꢀairꢀleaksꢀ  
withꢀanꢀautomotive-gradeꢀsealantꢀmaterial.  
Itꢀisꢀabsolutelyꢀvitalꢀthatꢀtheꢀspeakerꢀframeꢀ  
fitsꢀintoꢀtheꢀmountingꢀholeꢀcleanly.ꢀThisꢀmustꢀbeꢀ  
checkedꢀpriorꢀtoꢀtighteningꢀtheꢀscrews.ꢀDoꢀnotꢀ  
forceꢀtheꢀframeꢀintoꢀaꢀholeꢀthatꢀisꢀtooꢀsmall.ꢀDoꢀ  
notꢀtightenꢀtheꢀspeakerꢀontoꢀanꢀunevenꢀsurface.ꢀ  
Thisꢀwillꢀdamageꢀyourꢀspeakers.ꢀTheꢀspeakerꢀ  
shouldꢀalsoꢀfitꢀsoꢀthatꢀairꢀdoesꢀnotꢀleakꢀaroundꢀ  
theꢀmountingꢀflange.ꢀAirꢀleaksꢀwillꢀcauseꢀaꢀsevereꢀ  
degradationꢀinꢀsoundꢀquality.ꢀSealꢀanyꢀairꢀleaksꢀ  
withꢀanꢀautomotive-gradeꢀsealantꢀmaterial.  
Useꢀtheꢀsuppliedꢀmountingꢀclipsꢀunlessꢀtheꢀfactoryꢀ  
holesꢀalreadyꢀfeatureꢀthreadedꢀinserts.ꢀꢀꢀ  
Hand-tightenꢀtheꢀscrewsꢀevenlyꢀ(SeeꢀDiagramꢀI).ꢀ  
10 | JL Audio - C3-525 Owner’s Manual  
DIaGram I: Factory location woofer Installation  
DIaGram J: Custom location woofer Installation  
WARNING  
!!  
Hand-tighten the screws evenly in a criss-cross  
pattern to avoid bending the speaker frame or  
stripping the mounting clips.  
11  
TweeTer InsTallaTIon  
First,ꢀrunꢀspeakerꢀwiresꢀfromꢀtheꢀtweeterꢀoutputꢀ  
ofꢀtheꢀcrossoverꢀ(seeꢀWiringꢀDiagramꢀBꢀonꢀpageꢀ5)ꢀ  
toꢀtheꢀdesiredꢀtweeterꢀmountingꢀlocations,ꢀobservingꢀ  
theꢀsameꢀprecautionsꢀasꢀmentionedꢀinꢀtheꢀwooferꢀ  
installationꢀsection.ꢀTerminateꢀtheꢀwiresꢀwithꢀtheꢀ  
suppliedꢀ2.8ꢀmmꢀmaleꢀcrimpableꢀconnectors.  
surface-mount Installation  
Inꢀthisꢀapplication,ꢀyouꢀwillꢀnotꢀneedꢀtoꢀcutꢀ  
largeꢀholesꢀinꢀyourꢀvehicle’sꢀpanelsꢀforꢀtheꢀtweeters.ꢀ  
Youꢀwillꢀonlyꢀneedꢀtoꢀdrillꢀaꢀholeꢀforꢀtheꢀwiresꢀandꢀ  
twoꢀsmallerꢀholesꢀforꢀtheꢀmountingꢀscrews.ꢀThisꢀ  
applicationꢀisꢀusefulꢀwhenꢀmountingꢀtheꢀtweetersꢀtoꢀ  
aꢀpanelꢀthatꢀhasꢀinsufficientꢀclearanceꢀbehindꢀitꢀforꢀ  
theꢀtweeter’sꢀmagnetꢀstructure.  
TweeTer FIXTure InsTallaTIon:  
Theꢀdomeꢀtweetersꢀsuppliedꢀwithꢀyourꢀꢀ  
Usingꢀtheꢀfixtureꢀasꢀaꢀtemplate,ꢀmarkꢀtheꢀscrewꢀ  
holeꢀlocationsꢀandꢀaꢀlocationꢀinꢀtheꢀcenterꢀofꢀtheꢀ  
fixtureꢀforꢀtheꢀwireꢀhole.ꢀRemoveꢀtheꢀfixtureꢀandꢀ  
drillꢀpilotꢀholesꢀforꢀtheꢀscrewsꢀandꢀaꢀ1/4-inchꢀ(6.4ꢀ  
mm)ꢀforꢀtheꢀwires.ꢀUseꢀtheꢀsuppliedꢀ#6ꢀxꢀ1.00-inchꢀ  
sheetꢀmetalꢀscrewsꢀtoꢀsecureꢀtheꢀfixtureꢀasꢀshownꢀinꢀ  
DiagramꢀL.ꢀNext,ꢀrouteꢀtheꢀtweeter’sꢀpositiveꢀ(+)ꢀandꢀ  
negativeꢀ(-)ꢀwireꢀleadsꢀthroughꢀtheꢀ1/4-inchꢀcenterꢀ  
hole.ꢀTheꢀtweeterꢀisꢀsecuredꢀtoꢀtheꢀfixtureꢀusingꢀaꢀ  
simpleꢀbayonetꢀ(twistꢀandꢀlock)ꢀmechanism.ꢀToꢀattachꢀ  
theꢀtweeterꢀtoꢀtheꢀsurface-mountꢀfixture,ꢀobserveꢀtheꢀ  
indentedꢀlockingꢀslotsꢀonꢀtheꢀouterꢀedgeꢀofꢀtheꢀtweeterꢀ  
bodyꢀandꢀalignꢀtheseꢀwithꢀtheꢀtabsꢀvisibleꢀonꢀtheꢀ  
insideꢀwallsꢀofꢀtheꢀfixture.ꢀTheꢀtweeterꢀshouldꢀslideꢀ  
intoꢀplaceꢀeasilyꢀandꢀcanꢀthenꢀbeꢀlockedꢀbyꢀpushingꢀ  
downꢀonꢀtheꢀtweeterꢀandꢀgivingꢀitꢀaꢀsmallꢀclockwiseꢀ  
turnꢀ(SeeꢀDiagramꢀL).  
C3-525ꢀsystemꢀhaveꢀbeenꢀdesignedꢀforꢀmaximumꢀ  
mountingꢀversatilityꢀinꢀaꢀcomponentꢀconfiguration.ꢀ  
Thereꢀareꢀtwoꢀprimaryꢀmethodsꢀbyꢀwhichꢀtheꢀ  
tweetersꢀcanꢀbeꢀmountedꢀinꢀyourꢀvehicle:  
Flush-mount Installation  
Theꢀdomeꢀtweetersꢀsuppliedꢀwithꢀyourꢀꢀ  
C3-525ꢀsystemꢀhaveꢀbeenꢀdesignedꢀtoꢀintegrateꢀwithꢀ  
yourꢀinstallationꢀinꢀaꢀclean,ꢀunobtrusiveꢀmannerꢀ  
usingꢀaꢀflush-mountꢀcup.ꢀThisꢀcompactꢀmountingꢀ  
fixtureꢀisꢀinstalledꢀusingꢀtheꢀmethodꢀillustratedꢀinꢀ  
DiagramꢀKꢀandꢀrequiresꢀaꢀmountingꢀholeꢀwithꢀaꢀ  
diameterꢀofꢀ1.875ꢀin.ꢀ(47.6ꢀmm).ꢀ  
Atꢀleastꢀ1.70-inchꢀ(43.2ꢀmm)ꢀofꢀclearanceꢀisꢀ  
requiredꢀbehindꢀtheꢀmountingꢀsurfaceꢀofꢀtheꢀtweeterꢀ  
forꢀtheꢀspringꢀclipsꢀandꢀ1-inchꢀmachineꢀscrewsꢀ  
usedꢀinꢀmountingꢀtheꢀfixture.ꢀInꢀlimitedꢀdepthꢀ  
applications,ꢀitꢀmayꢀbeꢀnecessaryꢀtoꢀcutꢀdownꢀtheꢀ  
lengthꢀofꢀtheꢀmachineꢀscrew,ꢀorꢀtoꢀuseꢀaꢀshorterꢀscrewꢀ  
(notꢀsupplied).ꢀHand-tightenꢀtheꢀmachineꢀscrewꢀuntilꢀ  
theꢀfixtureꢀisꢀsecureꢀ(SeeꢀDiagramꢀK).  
12 | JL Audio - C3-525 Owner’s Manual  
DIaGram K: Flush-mount Tweeter Installation  
DIaGram l: surface-mount Tweeter Installation  
13  
noTes  
14 | JL Audio - C3-525 Owner’s Manual  
noTes  
15  
lImITeD warranTY - auTomoTIVe sPeaKer sYsTems (usa)  
JLꢀAUDIOꢀwarrantsꢀtheseꢀspeakersꢀ(andꢀcrossoverꢀnetworks,ꢀwhereꢀapplicable)ꢀtoꢀbeꢀfreeꢀofꢀdefectsꢀinꢀ  
materialsꢀandꢀworkmanshipꢀforꢀaꢀperiodꢀofꢀone (1) year.  
Thisꢀwarrantyꢀisꢀnotꢀtransferableꢀandꢀappliesꢀonlyꢀtoꢀtheꢀoriginalꢀpurchaserꢀfromꢀanꢀauthorizedꢀꢀ  
JLꢀAUDIOꢀdealer.ꢀꢀShouldꢀserviceꢀbeꢀnecessaryꢀunderꢀthisꢀwarrantyꢀforꢀanyꢀreasonꢀdueꢀtoꢀmanufacturingꢀ  
defectꢀorꢀmalfunction,ꢀJLꢀAUDIOꢀwillꢀ(atꢀitsꢀdiscretion),ꢀrepairꢀorꢀreplaceꢀtheꢀdefectiveꢀproductꢀwithꢀnewꢀorꢀ  
remanufacturedꢀproductꢀatꢀnoꢀcharge.ꢀDamageꢀcausedꢀbyꢀtheꢀfollowingꢀisꢀnotꢀcoveredꢀunderꢀwarranty:ꢀaccident,ꢀ  
misuse,ꢀabuse,ꢀproductꢀmodificationꢀorꢀneglect,ꢀfailureꢀtoꢀfollowꢀinstallationꢀinstructions,ꢀunauthorizedꢀrepairꢀ  
attempts,ꢀmisrepresentationsꢀbyꢀtheꢀseller.ꢀꢀThisꢀwarrantyꢀdoesꢀnotꢀcoverꢀincidentalꢀorꢀconsequentialꢀdamagesꢀ  
andꢀdoesꢀnotꢀcoverꢀtheꢀcostꢀofꢀremovingꢀorꢀreinstallingꢀtheꢀunit(s).ꢀꢀCosmeticꢀdamageꢀdueꢀtoꢀaccidentꢀorꢀnormalꢀ  
wearꢀandꢀtearꢀisꢀnotꢀcoveredꢀunderꢀwarranty.  
Anyꢀapplicableꢀimpliedꢀwarrantiesꢀareꢀlimitedꢀinꢀdurationꢀtoꢀtheꢀperiodꢀofꢀtheꢀexpressꢀwarrantyꢀasꢀprovidedꢀ  
hereinꢀbeginningꢀwithꢀtheꢀdateꢀofꢀtheꢀoriginalꢀpurchaseꢀatꢀretail,ꢀandꢀnoꢀwarranties,ꢀwhetherꢀexpressꢀorꢀimplied,ꢀ  
shallꢀapplyꢀtoꢀthisꢀproductꢀthereafter.ꢀꢀSomeꢀstatesꢀdoꢀnotꢀallowꢀlimitationsꢀonꢀimpliedꢀwarranties,ꢀthereforeꢀ  
theseꢀexclusionsꢀmayꢀnotꢀapplyꢀtoꢀyou.ꢀꢀThisꢀwarrantyꢀgivesꢀyouꢀspecificꢀlegalꢀrights,ꢀandꢀyouꢀmayꢀalsoꢀhaveꢀotherꢀ  
rightsꢀwhichꢀvaryꢀfromꢀstateꢀtoꢀstate.  
If you need service on your Jl auDIo product:  
AllꢀwarrantyꢀreturnsꢀshouldꢀbeꢀsentꢀtoꢀJLꢀAUDIOꢀfreightꢀprepaidꢀthroughꢀanꢀauthorizedꢀJLꢀAUDIOꢀ  
dealerꢀandꢀmustꢀbeꢀaccompaniedꢀbyꢀproofꢀofꢀpurchaseꢀ(aꢀcopyꢀofꢀtheꢀoriginalꢀsalesꢀreceipt.)ꢀꢀDirectꢀ  
returnsꢀfromꢀconsumersꢀorꢀnon-authorizedꢀdealersꢀwillꢀbeꢀrefusedꢀunlessꢀspecificallyꢀauthorizedꢀbyꢀ  
JLꢀAUDIOꢀwithꢀaꢀvalidꢀreturnꢀauthorizationꢀnumber.ꢀꢀWarrantyꢀexpirationꢀonꢀproductsꢀreturnedꢀ  
withoutꢀproofꢀofꢀpurchaseꢀwillꢀbeꢀdeterminedꢀfromꢀtheꢀmanufacturingꢀdateꢀcode.ꢀCoverageꢀmayꢀbeꢀ  
invalidatedꢀasꢀthisꢀdateꢀisꢀpreviousꢀtoꢀpurchaseꢀdate.ꢀꢀReturnꢀonlyꢀdefectiveꢀcomponents.ꢀꢀIfꢀoneꢀspeakerꢀ  
failsꢀinꢀaꢀsystem,ꢀreturnꢀonlyꢀthatꢀspeakerꢀcomponent,ꢀnotꢀtheꢀentireꢀsystem.ꢀNon-defectiveꢀitemsꢀ  
receivedꢀwillꢀbeꢀreturnedꢀfreight-collect.ꢀꢀCustomerꢀisꢀresponsibleꢀforꢀshippingꢀchargesꢀandꢀinsuranceꢀ  
inꢀsendingꢀtheꢀproductꢀtoꢀJLꢀAUDIO.ꢀꢀFreightꢀdamageꢀonꢀreturnsꢀisꢀnotꢀcoveredꢀunderꢀwarranty.ꢀ  
For service Information in the u.s.a. please call  
Jl audio Customer service: (954) 443-1100  
9:00 AM – 5:30 PM (Eastern Time Zone)  
Jl audio, Inc  
10369 North Commerce Pkwy.  
Miramar, FL 33025  
(do not send product for repair to this address)  
International warranties:  
Products purchased outside the United States of America are covered only  
by that country’s distributor and not by JL Audio, Inc.  
Printed in China  
C3-525-020810  

Alpine MULTIMEDIA MANAGER PXA H701 User Manual
Audiovox MMD7HRT User Manual
Boss Audio Systems Boss Digital Panning Delay RPD 10 User Manual
Canon 3CCD User Manual
Canon Camcorder EOS REBEL User Manual
COBY electronic SNAPP CAM4505 User Manual
Focal Polyglass 33 V1 User Manual
Honeywell TRIPLEAQUASTAT L8151A User Manual
Ikelite MD200 User Manual
JBL GRAND TOURING GTO1202D User Manual