JL Audio C3 570 031010 User Manual

owner’s manual  
5-inch x 7-inch (125 x 180 mm) Convertible 2-Way Component System  
Thank you for choosing a JL Audio Evolution™ C3 Convertible  
Component System for your automotive sound system.  
These Evolution™ Speakers have been designed and manufactured to  
exacting standards in order to ensure years of musical enjoyment in your  
vehicle. For maximum performance and extended warranty  
coverage, we highly recommend that you have your new speakers installed  
by an authorized JL Audio dealer. Your authorized  
dealer has the training, expertise and installation equipment to ensure  
optimum performance from this product. Should you  
decide to install the speakers yourself, please take the time  
to read this manual thoroughly so as to familiarize yourself  
with its installation requirements and setup procedures.  
If you have any questions regarding the instructions in this  
manual or any aspect of your amplifier’s operation, please contact your  
authorized JL Audio dealer for assistance. If you need further assistance,  
please call the JL Audio Technical Support Department  
at (954) 443-1100 during business hours.  
C3-570 sPeCIFICaTIons  
Woofers: Injection-Molded Polymer Frame, Patented Elevated  
Frame Cooling (U.S. Patent #6,219,431 & #6,229,902), DMA-  
Optimized Motor System, Mineral-Filled Polypropylene Cone,  
Rubber Surround, 1.2-in. / 31 mm Voice Coil, Kapton® Former,  
Low-Profile, Symmetrical Roll Spider, Ferrite Magnet  
Included Components and Parts:  
• Two C3-570cw 5x7-inch (125 x 180 mm) Woofers  
• Two C3-100ct 1.00-inch (25 mm) Tweeters  
• Two C3-570-XO Crossover Networks  
• Two Surface-Mount Tweeter Fixtures  
• Two Coaxial-Mount Tweeter Fixtures  
• Two Flush-Mount Tweeter Fixtures  
Tweeters: 1.00 in. / 25 mm Silk Soft Dome with Ferrofluid  
Cooling and Damping and Neodymium Magnet  
Fixed Angle Flush-Mount, Surface-Mount and Coaxial-Mount  
Systems  
• Two Metal Spring Clips for Tweeter Fixtures  
• Two Woofer Spacer Gaskets  
• Twelve #8 x 1.25 inch (32 mm) Sheet Metal Screws  
• Four #6 x 1.00-inch (25 mm) Sheet Metal Screws  
• Two 1.00-inch (25 mm) Machine Screws  
• Eight Mounting Clips for Woofer Mounting  
• Two 6.4 mm Female Crimpable Connectors  
• Two 4.7 mm Male Crimpable Connectors  
• Two 4.7 mm Female Crimpable Connectors  
• Four 2.8 mm Female Crimpable Connectors  
• Two 2.8 mm Male Crimpable Connectors  
• Twelve Crimpable Spade Connectors  
• One Woofer Mounting Template  
Crossover Networks: 2-way networks with 1st order  
low-pass and 2nd order high-pass filters, premium Mylar®  
capacitors, air-core inductors, 4-position adjustable tweeter  
output level, 3-position midrange presence control,  
Polyswitch tweeter protection  
Continuous Power Handling: 75 Watts (RMS Method)  
Frequency Response: 48 Hz - 25 KHz ( 3 dB)  
Efficiency @ 1W/1m: 90.0 dB @ 1W/1m  
Nominal Impedance: 4 ohms  
Due to ongoing product development, all specifications are subject to change without notice.  
3
GeTTInG sTarTeD  
aDJusTaBle mIDranGe PresenCe  
•ꢀTurnꢀoffꢀtheꢀaudioꢀsystem.ꢀItꢀisꢀalsoꢀ  
advisableꢀtoꢀdisconnectꢀtheꢀnegativeꢀ(–)ꢀ  
terminalꢀofꢀyourꢀvehicle’sꢀbatteryꢀwheneverꢀ  
performingꢀinstallationꢀwork.  
•ꢀBeforeꢀcutting,ꢀdrillingꢀorꢀinsertingꢀanyꢀscrew,ꢀ  
checkꢀclearancesꢀonꢀbothꢀsidesꢀofꢀtheꢀplannedꢀ  
mountingꢀsurface.ꢀAlsoꢀcheckꢀforꢀanyꢀpotentialꢀ  
obstacles,ꢀsuchꢀasꢀwindowꢀtracksꢀandꢀmotors,ꢀ  
wiringꢀharnesses,ꢀetc.ꢀCheckꢀbothꢀsidesꢀofꢀtheꢀ  
YourꢀC3ꢀcrossoverꢀnetworksꢀprovideꢀaꢀuniqueꢀ  
midrangeꢀpresenceꢀcontrol,ꢀlocatedꢀunderꢀtheꢀcover.ꢀ  
Theꢀmidrangeꢀpresenceꢀisꢀselectableꢀviaꢀaꢀsetꢀofꢀpinsꢀ  
andꢀallowsꢀforꢀthreeꢀsettings.ꢀTheseꢀsettingsꢀaffectꢀtheꢀ  
amplitudeꢀofꢀtheꢀupperꢀmidrangeꢀresponseꢀofꢀtheꢀC3ꢀ  
componentꢀwoofer.ꢀWeꢀrecommendꢀthatꢀyouꢀbeginꢀ  
yourꢀlisteningꢀinꢀtheꢀ“REF”ꢀ(Reference)ꢀandꢀadjustꢀ  
upꢀorꢀdownꢀasꢀneededꢀtoꢀcompensateꢀforꢀmountingꢀ  
location,ꢀorientationꢀorꢀpersonalꢀtaste.  
vehicle,ꢀmanyꢀvehiclesꢀareꢀnotꢀsymmetrical!  
•ꢀAlwaysꢀwearꢀprotectiveꢀeyewear.  
CrossoVer neTworK InsTallaTIon  
TheꢀcrossoverꢀnetworksꢀsuppliedꢀwithꢀyourꢀC3ꢀ  
Systemꢀshouldꢀbeꢀinstalledꢀinꢀaꢀdryꢀlocationꢀinsideꢀ  
yourꢀvehicle.ꢀDOꢀNOTꢀINSTALLꢀTHEMꢀINSIDEꢀOFꢀ  
AꢀDOOR!ꢀDoorsꢀoftenꢀgetꢀwetꢀonꢀtheꢀinside,ꢀwhichꢀ  
canꢀdamageꢀyourꢀcrossoverꢀnetworksꢀandꢀcouldꢀ  
potentiallyꢀdamageꢀyourꢀentireꢀsoundꢀsystem.ꢀTheꢀ  
crossoversꢀcanꢀbeꢀscrewedꢀintoꢀaꢀsolidꢀsurfaceꢀviaꢀtwoꢀ  
holesꢀlocatedꢀunderꢀtheꢀprotectiveꢀcoverꢀofꢀtheꢀcase.ꢀ  
Toꢀaccessꢀtheseꢀholes,ꢀsimplyꢀsqueezeꢀtheꢀsidesꢀofꢀtheꢀ  
coverꢀwhileꢀgentlyꢀpullingꢀtheꢀcoverꢀawayꢀfromꢀtheꢀ  
base.ꢀMakeꢀsureꢀthatꢀyourꢀmountingꢀlocationꢀwillꢀnotꢀ  
causeꢀdamageꢀtoꢀwiring,ꢀfuelꢀlines,ꢀbrakeꢀlinesꢀorꢀanyꢀ  
otherꢀvitalꢀcomponentꢀofꢀyourꢀvehicle.ꢀOnceꢀyouꢀhaveꢀ  
screwedꢀtheꢀcaseꢀinꢀandꢀmadeꢀyourꢀconnections,ꢀsnapꢀ  
theꢀprotectiveꢀcoverꢀbackꢀintoꢀplace.ꢀ  
aDJusTaBle TweeTer leVel  
C3ꢀcrossoverꢀnetworksꢀalsoꢀprovideꢀfourꢀlevelsꢀ  
ofꢀtweeterꢀadjustabilityꢀdesignedꢀtoꢀcompensateꢀforꢀ  
differentꢀmountingꢀlocations,ꢀvehicleꢀinteriorsꢀandꢀ  
personalꢀtaste.ꢀTheseꢀlevelsꢀareꢀselectableꢀviaꢀaꢀsetꢀofꢀ  
pinsꢀlocatedꢀunderꢀtheꢀclearꢀcoverꢀofꢀeachꢀcrossoverꢀ  
case.ꢀWeꢀrecommendꢀthatꢀyouꢀbeginꢀlisteningꢀinꢀtheꢀ  
“REF”ꢀ(Reference)ꢀposition.ꢀToꢀfindꢀtheꢀoptimumꢀ  
tonalꢀbalanceꢀinꢀyourꢀinstallation,ꢀexperimentꢀwithꢀ  
alternateꢀtweeterꢀlevelꢀsettingsꢀbyꢀmovingꢀtheꢀpins.ꢀItꢀ  
isꢀsafeꢀtoꢀswitchꢀjumpersꢀwhileꢀtheꢀsystemꢀisꢀplaying.  
TweeTer ProTeCTIon  
TheꢀC3ꢀcrossoverꢀnetworksꢀareꢀequippedꢀwithꢀ  
anꢀadvancedꢀelectronicꢀtweeterꢀprotectionꢀcircuitꢀ  
designedꢀtoꢀminimizeꢀtheꢀpossibilityꢀofꢀtweeterꢀ  
failure.ꢀThisꢀelectronicꢀdeviceꢀmonitorsꢀcurrentꢀgoingꢀ  
toꢀtheꢀtweeterꢀandꢀwillꢀdisconnectꢀtheꢀtweeterꢀfromꢀ  
theꢀsignalꢀwhenꢀitꢀsensesꢀoverload.ꢀShouldꢀthisꢀoccurꢀ  
whileꢀlisteningꢀtoꢀtheꢀaudioꢀsystem,ꢀsimplyꢀreduceꢀtheꢀ  
volumeꢀforꢀaꢀfewꢀsecondsꢀandꢀtheꢀprotectionꢀcircuitꢀ  
willꢀresetꢀitselfꢀautomatically.  
CrossoVer neTworK aDJusTmenT  
Theꢀcrossoverꢀnetworksꢀhaveꢀbeenꢀdesignedꢀtoꢀ  
allowꢀtonalꢀadjustmentsꢀtoꢀtheꢀupperꢀmidrangeꢀ  
responseꢀandꢀtweeterꢀlevel.ꢀTheseꢀadjustmentsꢀmakeꢀ  
itꢀpossibleꢀtoꢀfine-tuneꢀyourꢀsystemꢀtoꢀsuitꢀyourꢀ  
listeningꢀpreferencesꢀandꢀtoꢀcompensateꢀforꢀvariousꢀ  
speakerꢀmountingꢀapplications.ꢀ  
4 | JL Audio - C3-570 Owner’s Manual  
wIrInG Your sPeaKer sYsTem  
C3ꢀConvertibleꢀComponentsꢀgiveꢀyouꢀtheꢀoptionꢀ  
ofꢀinstallingꢀtheꢀspeakersꢀasꢀseparateꢀcomponentꢀ  
speakerꢀsystemsꢀorꢀasꢀcoaxialꢀsystemsꢀ(tweetersꢀ  
mountedꢀontoꢀtheꢀcenterꢀofꢀeachꢀwoofer).  
Positiveꢀ(+)ꢀandꢀnegativeꢀ(–)ꢀconnectionsꢀtoꢀtheꢀ  
crossoverꢀfromꢀtheꢀamplifierꢀoutputsꢀareꢀmadeꢀwithꢀ  
theꢀterminalsꢀlabeledꢀ“IN+”ꢀandꢀ“IN–”.ꢀTheꢀPositiveꢀ  
andꢀNegativeꢀoutputsꢀtoꢀtheꢀwooferꢀconnectionsꢀareꢀ  
labeledꢀ“W+”ꢀandꢀ“W–”onꢀtheꢀCrossoverꢀandꢀshouldꢀ  
beꢀconnectedꢀtoꢀcorrespondingꢀ“WFR+”ꢀandꢀꢀ  
WFR–”ꢀterminalsꢀonꢀtheꢀwooferꢀ(asꢀillustratedꢀ  
below).ꢀTheꢀtweeterꢀconnectionsꢀvaryꢀbyꢀsystemꢀ  
configurationꢀandꢀmayꢀbeꢀmadeꢀinꢀoneꢀofꢀtwoꢀways.ꢀ  
Inꢀcomponentꢀconfiguration,ꢀtheꢀtweeterꢀoutputs,ꢀ  
labeledꢀ“T+”ꢀandꢀ“T”ꢀonꢀtheꢀCrossoverꢀshouldꢀbeꢀwiredꢀ  
directlyꢀtoꢀtheꢀcorrespondingꢀleadꢀonꢀtheꢀtweeterꢀ(Seeꢀ  
DiagramꢀA).ꢀInꢀcoaxialꢀconfiguration,ꢀtheꢀtweeterꢀisꢀ  
connectedꢀviaꢀanꢀinternalꢀjumperꢀ(Seeꢀpageꢀ6ꢀforꢀmoreꢀ  
information)ꢀandꢀtheꢀCrossoverꢀtweeterꢀoutputsꢀshouldꢀ  
beꢀwiredꢀtoꢀtheꢀcorrespondingꢀ“TWT+”ꢀandꢀ“TWT”ꢀ  
terminalsꢀonꢀtheꢀwooferꢀ(SeeꢀDiagramꢀB).ꢀ  
WARNING  
!!  
It is absolutely vital that your component system  
is connected as shown in this manual. Failure to  
connect the system as shown may result in damage to  
your speakers which is NOT covered under warranty.  
DIaGram a: Component system wiring  
Do not substitute different crossover networks into  
your C3 System. Do not use crossover networks  
intended for different C3 models.  
Amplifier  
Output  
Red  
Black  
DIaGram B: Coaxial system wiring  
Amplifier  
Output  
Red  
Black  
5
ConVerTIBle ComPonenTs  
C3ꢀConvertibleꢀComponentsꢀgiveꢀyouꢀtheꢀoptionꢀ  
ofꢀinstallingꢀtheꢀspeakersꢀasꢀseparateꢀcomponentꢀ  
speakerꢀsystemsꢀorꢀasꢀcoaxialꢀsystemsꢀ(tweetersꢀ  
mountedꢀontoꢀtheꢀcenterꢀofꢀeachꢀwoofer).  
Coaxial system set-up  
TheꢀCoaxialꢀconfigurationꢀofꢀtheꢀC3-570ꢀisꢀ  
achievedꢀbyꢀinstallingꢀaꢀtweeterꢀontoꢀtheꢀcenterꢀofꢀ  
eachꢀwooferꢀusingꢀtheꢀsuppliedꢀcoaxialꢀtweeterꢀposts.  
First,ꢀremoveꢀtheꢀphaseꢀplugsꢀfromꢀtheꢀwoofersꢀ(ifꢀ  
present)ꢀbyꢀpushingꢀdownꢀfirmly/evenlyꢀonꢀtheꢀplugꢀ  
withꢀthumbꢀandꢀindexꢀfingerꢀandꢀturningꢀ1/4ꢀturnꢀ  
counter-clockwiseꢀtoꢀunlockꢀandꢀremove.ꢀTheꢀphaseꢀ  
plugsꢀwillꢀnotꢀbeꢀusedꢀinꢀcoaxialꢀconfigurationꢀandꢀ  
shouldꢀbeꢀsetꢀasideꢀforꢀpossibleꢀfutureꢀuse.  
Note: If the C3 system is to be used in a coaxial  
configuration, the phase plugs must be removed to  
accept the tweeter and tweeter post.  
Component system set-up  
TheꢀComponentꢀconfigurationꢀofꢀtheꢀC3-570ꢀ  
isꢀachievedꢀbyꢀwiringꢀtheꢀtweeterꢀtoꢀtheꢀcrossoverꢀ  
separatelyꢀandꢀinstallingꢀtheꢀincludedꢀphaseꢀplugsꢀ  
ontoꢀtheꢀcenterꢀofꢀeachꢀwoofer.ꢀThe woofers are  
factory-packaged in the component system  
configuration with phase plugs installed.  
Theꢀphaseꢀplugsꢀattachꢀtoꢀtheꢀwoofersꢀusingꢀaꢀ  
simpleꢀbayonetꢀ(twistꢀandꢀlock)ꢀmechanism.ꢀ  
Toꢀremoveꢀtheꢀphaseꢀplugs,ꢀsimplyꢀapplyꢀ  
downwardꢀpressureꢀwithꢀyourꢀthumbꢀandꢀindexꢀ  
fingerꢀandꢀtwistꢀ1/4ꢀturnꢀcounteclockwiseꢀuntilꢀ  
released.ꢀThenꢀpullꢀtheꢀphaseꢀplugꢀoffꢀtheꢀreceiver.  
Toꢀreattachꢀtheꢀphaseꢀplugs,ꢀalignꢀtheꢀtwoꢀ  
tabsꢀonꢀtheꢀinsideꢀofꢀeachꢀphaseꢀplugꢀwithꢀtheꢀ  
groovesꢀonꢀtheꢀouterꢀdiameterꢀofꢀtheꢀreceiverꢀ  
inꢀtheꢀcenterꢀofꢀtheꢀwoofer.ꢀWithꢀtheseꢀaligned,ꢀ  
slideꢀtheꢀphaseꢀplugꢀdownꢀintoꢀplaceꢀuntilꢀitꢀ  
stops,ꢀapplyingꢀgentleꢀpressure.ꢀToꢀlock,ꢀpushꢀ  
downꢀfirmly/evenlyꢀonꢀtheꢀplugꢀwithꢀthumbꢀandꢀ  
indexꢀfingerꢀandꢀturnꢀ1/4ꢀturnꢀclockwise.ꢀ  
Forꢀwooferꢀmountingꢀinstructions,ꢀpleaseꢀreferꢀ  
toꢀPagesꢀ10-11ꢀofꢀthisꢀManual.ꢀForꢀseparateꢀtweeterꢀ  
mountingꢀinstructions,ꢀpleaseꢀreferꢀtoꢀPagesꢀ12-13ꢀofꢀ  
thisꢀManual.  
Next,ꢀrouteꢀtheꢀtweeter’sꢀPositiveꢀ(+)ꢀandꢀꢀ  
Negativeꢀ(-)ꢀwireꢀleadsꢀthroughꢀtheꢀcenterꢀofꢀtheꢀ  
coaxialꢀtweeterꢀpostꢀfromꢀtheꢀlargeꢀtweeter-cupꢀendꢀ  
andꢀoutꢀtheꢀsmallerꢀendꢀ(SeeꢀFigureꢀA).ꢀTheꢀtweeterꢀ  
mountsꢀtoꢀtheꢀcoaxialꢀtweeterꢀpostꢀusingꢀaꢀsimpleꢀ  
bayonetꢀ(twistꢀandꢀlock)ꢀmechanism.ꢀToꢀattachꢀtheꢀ  
tweeterꢀtoꢀtheꢀpost,ꢀobserveꢀtheꢀindentedꢀlockingꢀ  
slotsꢀonꢀtheꢀouterꢀedgeꢀofꢀtheꢀtweeterꢀbodyꢀandꢀalignꢀ  
theseꢀwithꢀtheꢀtabsꢀvisibleꢀonꢀtheꢀinsideꢀwallsꢀofꢀtheꢀ  
tweeterꢀcupꢀportionꢀofꢀtheꢀtweeterꢀpost.ꢀTheꢀtweeterꢀ  
shouldꢀslideꢀintoꢀplaceꢀeasilyꢀandꢀcanꢀthenꢀbeꢀlockedꢀ  
byꢀpushingꢀdownꢀonꢀtheꢀtweeterꢀandꢀgivingꢀitꢀaꢀsmallꢀ  
clockwiseꢀturnꢀ(SeeꢀFigureꢀB).ꢀ  
Withꢀtheꢀtweeterꢀinstalledꢀintoꢀtheꢀtweeterꢀpost,ꢀ  
connectꢀtheꢀPositiveꢀ(+)ꢀredꢀwireꢀleadꢀonꢀtheꢀtweeterꢀ  
toꢀtheꢀlargerꢀmaleꢀconnectionꢀtabꢀinꢀtheꢀwoofer’sꢀ  
center,ꢀfollowedꢀinꢀtheꢀsameꢀmanner,ꢀbyꢀtheꢀꢀ  
Negativeꢀ(-)ꢀblackꢀleadꢀtoꢀtheꢀsmallerꢀconnectionꢀtab.ꢀ  
(SeeꢀFigureꢀC).  
Now,ꢀnoteꢀtheꢀtwoꢀtabsꢀonꢀtheꢀinsideꢀofꢀtheꢀbottomꢀ  
endꢀofꢀtheꢀtweeterꢀpost.ꢀAlignꢀtheseꢀtabsꢀtoꢀtheꢀ  
channelsꢀvisibleꢀonꢀoppositeꢀsidesꢀofꢀtheꢀreceiverꢀinꢀ  
theꢀwoofer’sꢀcenter.ꢀWhileꢀtuckingꢀtheꢀwiresꢀintoꢀtheꢀ  
tweeterꢀpost,ꢀslideꢀtheꢀtweeterꢀpostꢀdownꢀintoꢀplaceꢀ  
untilꢀitꢀstopsꢀandꢀisꢀreadyꢀtoꢀbeꢀlocked.ꢀToꢀlock,ꢀpushꢀ  
downꢀfirmly/evenlyꢀonꢀtheꢀtweeterꢀpostꢀwithꢀthumbꢀ  
andꢀindexꢀfingerꢀandꢀturnꢀ1/4ꢀturnꢀclockwise.ꢀꢀ  
(SeeꢀFigureꢀD).  
Forꢀwooferꢀmountingꢀinstructions,ꢀpleaseꢀreferꢀtoꢀ  
Pagesꢀ10-11ꢀofꢀthisꢀManual.ꢀ  
6 | JL Audio - C3-570 Owner’s Manual  
DIaGram C: Tweeter Post / Coaxial system Configuration  
FigureꢀA.  
FigureꢀB.  
FigureꢀC.  
FigureꢀD.  
DIaGram D: Phase Plug / Component system Configuration  
7
CoaXIal PlaCemenT ConsIDeraTIons  
Inꢀmostꢀcases,ꢀspeakersꢀinꢀtheꢀcoaxialꢀ  
ComPonenT PlaCemenT ConsIDeraTIons  
Aꢀcomponentꢀsystemꢀconfigurationꢀgivesꢀyouꢀtheꢀ  
abilityꢀtoꢀplaceꢀtheꢀwooferꢀandꢀtweeterꢀseparatelyꢀ  
inꢀyourꢀvehicleꢀinterior.ꢀThisꢀcanꢀbeꢀgoodꢀorꢀbad,ꢀ  
dependingꢀonꢀhowꢀit’sꢀdone.ꢀAsꢀaꢀgeneralꢀrule,ꢀtheꢀ  
tweetersꢀshouldꢀbeꢀplacedꢀrelativelyꢀcloseꢀtoꢀtheꢀ  
woofersꢀforꢀbestꢀtonalꢀbalanceꢀandꢀmostꢀcoherentꢀ  
imagingꢀ(theꢀcloser,ꢀtheꢀbetter).ꢀAnyꢀseparationꢀ  
greaterꢀthanꢀ8ꢀinchesꢀ(20ꢀcm)ꢀisꢀlikelyꢀtoꢀresultꢀinꢀ  
degradedꢀsoundꢀqualityꢀ(SeeꢀDiagramꢀH).ꢀ  
configurationꢀwillꢀbeꢀplacedꢀintoꢀfactoryꢀspeakerꢀ  
locations.ꢀIfꢀyouꢀhaveꢀsomeꢀspeakerꢀmountingꢀ  
flexibility,ꢀkeepꢀtheꢀfollowingꢀinꢀmind:ꢀLowerꢀ  
mountingꢀlocations,ꢀsuchꢀasꢀtheꢀlowerꢀfrontꢀcornerꢀ  
(SeeꢀDiagramꢀF)ꢀofꢀaꢀdoorꢀorꢀaꢀkick-panelꢀprovideꢀ  
theꢀgreatestꢀpathꢀlengthꢀdistancesꢀforꢀtheꢀsoundꢀ  
emittedꢀbyꢀtheꢀspeakers.ꢀForꢀthisꢀreason,ꢀtheyꢀareꢀ  
generallyꢀmoreꢀdesirableꢀthanꢀhigherꢀmountingꢀ  
locations.ꢀHigherꢀmountingꢀlocationsꢀwillꢀusuallyꢀ  
resultꢀinꢀextremeꢀnear-sideꢀsoundstageꢀbiasꢀwhichꢀ  
compromisesꢀtheꢀstereoꢀlisteningꢀexperienceꢀꢀ  
(SeeꢀDiagramꢀE).ꢀ  
Avoidꢀplacingꢀtweetersꢀwhereꢀtheyꢀwillꢀbeꢀblockedꢀ  
DIaGram e: CoaXIal ConFIGuraTIon - less Desirable Door speaker Placement  
DIaGram F: CoaXIal ConFIGuraTIon - more Desirable Door speaker Placement  
8 | JL Audio - C3-570 Owner’s Manual  
byꢀobjectsꢀinꢀtheꢀinteriorꢀofꢀtheꢀcarꢀ(includingꢀseatedꢀ  
occupants).ꢀWhenꢀselectingꢀaꢀmountingꢀlocation,ꢀ  
lookꢀatꢀbothꢀsidesꢀofꢀtheꢀcarꢀtoꢀmakeꢀsureꢀthatꢀthisꢀ  
locationꢀisꢀclearꢀonꢀbothꢀsides.ꢀ  
Youꢀcanꢀalwaysꢀexperimentꢀwithꢀtweeterꢀ  
placementꢀbeforeꢀcommittingꢀtoꢀaꢀfinalꢀmountingꢀ  
location.ꢀSimplyꢀconnectꢀtheꢀrestꢀofꢀtheꢀsystemꢀandꢀ  
allowꢀplentyꢀofꢀwireꢀlengthꢀforꢀtheꢀtweeters.ꢀUsingꢀ  
Velcro®ꢀorꢀsimilarꢀmaterial,ꢀattachꢀtheꢀtweetersꢀinꢀ  
differentꢀlocationsꢀuntilꢀyouꢀfindꢀtheꢀoneꢀwhereꢀtheyꢀ  
performꢀbest.  
Woofersꢀwillꢀusuallyꢀbeꢀplacedꢀintoꢀfactoryꢀ  
speakerꢀlocations.ꢀIfꢀyouꢀhaveꢀsomeꢀwooferꢀmountingꢀ  
flexibility,ꢀkeepꢀtheꢀfollowingꢀinꢀmind:ꢀLowerꢀ  
mountingꢀlocations,ꢀsuchꢀasꢀtheꢀlowerꢀfrontꢀcornerꢀofꢀ  
aꢀdoorꢀ(SeeꢀDiagramꢀH)ꢀorꢀaꢀkick-panelꢀprovideꢀtheꢀ  
greatestꢀpathꢀlengthꢀdistancesꢀforꢀtheꢀsoundꢀemittedꢀ  
byꢀtheꢀwoofer.ꢀForꢀthisꢀreason,ꢀtheyꢀareꢀgenerallyꢀ  
moreꢀdesirableꢀthanꢀhigherꢀmountingꢀlocations.ꢀ  
Higherꢀmountingꢀlocationsꢀoftenꢀresultꢀinꢀextremeꢀ  
near-sideꢀsoundstageꢀbiasꢀwhichꢀcompromisesꢀtheꢀ  
stereoꢀlisteningꢀexperienceꢀꢀ  
(SeeꢀDiagramꢀG).ꢀ  
DIaGram G: ComPonenT ConFIGuraTIon - less Desirable Door speaker Placement  
DIaGram H: ComPonenT ConFIGuraTIon - more Desirable Door speaker Placement  
9
WARNING  
!!  
Double check the clearance for both speakers  
before proceeding. Many cars are different from  
one side to the other!  
Connectꢀtheꢀspeakerꢀwiresꢀtoꢀbothꢀsetsꢀofꢀ  
terminalsꢀonꢀeachꢀspeaker,ꢀobservingꢀcorrectꢀ  
polarityꢀandꢀmakingꢀsureꢀthatꢀtheꢀtweeterꢀandꢀ  
wooferꢀwiresꢀcorrespondꢀtoꢀtheꢀcorrectꢀterminalsꢀ  
onꢀbothꢀtheꢀspeakerꢀandꢀtheꢀcrossover.ꢀ  
wooFer InsTallaTIon  
Theꢀwoofersꢀshouldꢀbeꢀinstalledꢀinꢀoneꢀofꢀtheꢀ  
followingꢀwaysꢀdependingꢀonꢀlocation:  
Factory location:ꢀIfꢀyouꢀwillꢀbeꢀusingꢀtheꢀfactoryꢀ  
speakerꢀwires,ꢀitꢀmayꢀbeꢀnecessaryꢀtoꢀchangeꢀtheꢀ  
terminations.ꢀThisꢀmayꢀbeꢀaccomplishedꢀbyꢀusingꢀ  
anꢀadaptorꢀplugꢀorꢀsimplyꢀbyꢀcuttingꢀtheꢀfactoryꢀ  
connectorꢀoffꢀandꢀusingꢀtheꢀsuppliedꢀcrimpꢀ  
connectorsꢀtoꢀterminateꢀtheꢀspeakerꢀwires.ꢀTheꢀ  
Secureꢀtheꢀspeakerꢀandꢀspacerꢀgasketꢀ(ifꢀ  
applicable)ꢀtoꢀtheꢀpanelꢀbyꢀevenlyꢀtighteningꢀ  
byꢀhandꢀmountingꢀscrews.ꢀUseꢀtheꢀsuppliedꢀ  
mountingꢀclipsꢀandꢀtheꢀtheꢀprovidedꢀ#8ꢀxꢀ1.25ꢀ  
inchꢀ(32ꢀmm)ꢀmountingꢀscrewsꢀunlessꢀtheꢀ  
factoryꢀholesꢀalreadyꢀfeatureꢀthreadedꢀinserts.ꢀ  
Custom location:ꢀRunꢀspeakerꢀwireꢀtoꢀtheꢀ  
desiredꢀmountingꢀlocations.ꢀIfꢀyouꢀareꢀrunningꢀ  
wiresꢀintoꢀaꢀdoor,ꢀuseꢀexistingꢀfactoryꢀwiringꢀbootsꢀ  
wheneverꢀpossible.ꢀIfꢀyouꢀareꢀdrillingꢀnewꢀholes,ꢀfileꢀ  
theirꢀedgesꢀandꢀinstallꢀrubberꢀgrommetsꢀintoꢀeachꢀ  
hole.ꢀWiresꢀshouldꢀthenꢀbeꢀcoveredꢀwithꢀaꢀprotective,ꢀ  
flexibleꢀPVCꢀsleeveꢀandꢀthenꢀrunꢀthroughꢀtheꢀdoorꢀ  
jamb.ꢀMakeꢀsureꢀthatꢀtheꢀwiresꢀwillꢀclearꢀdoorꢀhingesꢀ  
andꢀotherꢀstructuresꢀinꢀtheꢀdoor.ꢀIfꢀyouꢀareꢀunsureꢀ  
aboutꢀanyꢀpartꢀofꢀthisꢀprocess,ꢀpleaseꢀcontactꢀyourꢀꢀ  
JLꢀAudioꢀdealerꢀforꢀinstallationꢀhelp.ꢀ  
Selectꢀanꢀevenꢀsurface.ꢀTighteningꢀaꢀspeakerꢀontoꢀ  
anꢀunevenꢀsurfaceꢀcanꢀdamageꢀit.ꢀUseꢀtheꢀsuppliedꢀ  
templateꢀtoꢀmarkꢀtheꢀdesiredꢀmountingꢀlocation.ꢀ  
Markꢀtheꢀcenterꢀandꢀtheꢀoutlineꢀofꢀtheꢀmountingꢀ  
holeꢀasꢀwellꢀasꢀtheꢀmountingꢀscrewꢀpositions.ꢀ  
Beforeꢀdrillingꢀorꢀcuttingꢀonꢀyourꢀinteriorꢀpanels,ꢀ  
useꢀaꢀutilityꢀknifeꢀtoꢀcutꢀanyꢀfabric,ꢀvinylꢀorꢀleatherꢀ  
fromꢀholeꢀlocations.ꢀTheseꢀmaterialsꢀcanꢀeasilyꢀ  
beꢀsnaggedꢀbyꢀaꢀdrillꢀorꢀaꢀsaw,ꢀcausingꢀdamageꢀtoꢀ  
theꢀpanelꢀandꢀpossibleꢀbodilyꢀinjury.ꢀDrillꢀfourꢀ  
1/8-inchꢀ(3ꢀmm)ꢀholesꢀforꢀtheꢀspeaker’sꢀmountingꢀ  
screwsꢀatꢀtheꢀpositionsꢀyouꢀhaveꢀmarked.ꢀAlsoꢀdrillꢀ  
aꢀpilotꢀholeꢀinꢀtheꢀcenterꢀofꢀtheꢀspeakerꢀmountingꢀ  
holeꢀatꢀthisꢀtime.ꢀThen,ꢀusingꢀaꢀsaberꢀsaw,ꢀmakeꢀ  
theꢀcircularꢀcutꢀoutꢀforꢀtheꢀspeaker.ꢀFileꢀanyꢀroughꢀ  
edges.ꢀInsertꢀtheꢀmountingꢀclipsꢀwithꢀtheꢀflatꢀsideꢀ  
towardsꢀtheꢀspeakerꢀasꢀshownꢀinꢀDiagramꢀI.  
largeꢀconnectorꢀisꢀforꢀtheꢀpositiveꢀ( )ꢀterminalꢀandꢀ  
+
theꢀsmallꢀconnectorꢀisꢀforꢀtheꢀnegativeꢀ(–)ꢀterminalꢀ  
ofꢀeachꢀwoofer.ꢀKeepꢀinꢀmindꢀthatꢀtheꢀwooferꢀwiresꢀ  
mustꢀbeꢀconnectedꢀtoꢀtheꢀwooferꢀoutputsꢀofꢀtheꢀ  
crossoversꢀsuppliedꢀwithꢀyourꢀsystemꢀasꢀshownꢀinꢀtheꢀ  
diagramꢀonꢀpageꢀ5.ꢀIfꢀyouꢀpreferꢀtoꢀrunꢀnewꢀwires,ꢀ  
referꢀtoꢀtheꢀ“CustomꢀLocation”ꢀinstallationꢀsectionꢀ  
forꢀdetails.ꢀWhicheverꢀmethodꢀyouꢀchoose,ꢀobserveꢀ  
correctꢀpolarityꢀinꢀyourꢀconnections.ꢀIfꢀyouꢀareꢀ  
unsureꢀaboutꢀanyꢀofꢀtheseꢀissues,ꢀcontactꢀyourꢀꢀ  
JLꢀAudioꢀdealerꢀforꢀinstallationꢀassistance.  
Yourꢀnewꢀspeakersꢀhaveꢀbeenꢀdesignedꢀ  
toꢀinstall,ꢀwithoutꢀmodifications,ꢀintoꢀmostꢀ  
vehiclesꢀthatꢀacceptꢀaꢀ5x7-inchꢀ(125ꢀxꢀ180ꢀmm)ꢀ  
speaker.ꢀMostꢀfactoryꢀ5x7-inchꢀspeakersꢀuseꢀ  
fourꢀmountingꢀscrewsꢀwhichꢀwillꢀlineꢀupꢀwithꢀ  
theꢀmountingꢀholesꢀonꢀyourꢀspeakers.ꢀ  
Aꢀspacerꢀgasketꢀhasꢀbeenꢀincludedꢀtoꢀfine-tuneꢀ  
speakerꢀfitment.ꢀThisꢀgasketꢀcanꢀbeꢀmountedꢀonꢀtheꢀ  
frontꢀofꢀtheꢀmountingꢀflange,ꢀtheꢀbackꢀofꢀtheꢀmountingꢀ  
flangeꢀorꢀsimplyꢀnotꢀbeꢀusedꢀinꢀtheꢀinstallation.ꢀ  
Itꢀisꢀabsolutelyꢀvitalꢀthatꢀtheꢀspeakerꢀframeꢀ  
fitsꢀintoꢀtheꢀmountingꢀholeꢀcleanly.ꢀThisꢀmustꢀbeꢀ  
checkedꢀpriorꢀtoꢀtighteningꢀtheꢀscrews.ꢀDoꢀnotꢀ  
forceꢀtheꢀframeꢀintoꢀaꢀholeꢀthatꢀisꢀtooꢀsmall.ꢀDoꢀ  
notꢀtightenꢀtheꢀspeakerꢀontoꢀanꢀunevenꢀsurface.ꢀ  
Thisꢀwillꢀdamageꢀyourꢀspeakers.ꢀTheꢀspeakerꢀ  
shouldꢀalsoꢀfitꢀsoꢀthatꢀairꢀdoesꢀnotꢀleakꢀaroundꢀ  
theꢀmountingꢀflange.ꢀAirꢀleaksꢀwillꢀcauseꢀaꢀsevereꢀ  
degradationꢀinꢀsoundꢀquality.ꢀSealꢀanyꢀairꢀleaksꢀ  
withꢀanꢀautomotive-gradeꢀsealantꢀmaterial.  
Itꢀisꢀabsolutelyꢀvitalꢀthatꢀtheꢀspeakerꢀframeꢀ  
fitsꢀintoꢀtheꢀmountingꢀholeꢀcleanly.ꢀThisꢀmustꢀbeꢀ  
10 | JL Audio - C3-570 Owner’s Manual  
DIaGram I: Factory /Custom location woofer  
checkedꢀpriorꢀtoꢀtighteningꢀtheꢀscrews.ꢀDoꢀnotꢀ  
tightenꢀtheꢀspeakerꢀontoꢀanꢀunevenꢀsurface!ꢀThisꢀ  
willꢀdamageꢀyourꢀspeakers.ꢀTheꢀspeakerꢀshouldꢀ  
alsoꢀfitꢀsoꢀthatꢀnoꢀairꢀleaksꢀaroundꢀtheꢀmountingꢀ  
flange.ꢀAirꢀleaksꢀwillꢀcauseꢀaꢀsevereꢀdegradationꢀ  
inꢀsoundꢀquality.ꢀSealꢀanyꢀairꢀleaksꢀwithꢀsilicone,ꢀ  
ropeꢀcaulkꢀorꢀsimilarꢀsealantꢀmaterial.ꢀ  
Installation options  
Aꢀspacerꢀgasketꢀhasꢀbeenꢀincludedꢀtoꢀ  
fine-tuneꢀspeakerꢀfitment.ꢀThisꢀgasketꢀcanꢀ  
beꢀmountedꢀonꢀtheꢀfrontꢀofꢀtheꢀmountingꢀ  
flange,ꢀtheꢀbackꢀofꢀtheꢀmountingꢀflangeꢀorꢀ  
simplyꢀnotꢀbeꢀusedꢀinꢀtheꢀinstallation.  
Connectꢀtheꢀspeakerꢀwiresꢀtoꢀbothꢀsetsꢀofꢀ  
terminalsꢀonꢀeachꢀspeaker,ꢀobservingꢀcorrectꢀ  
polarityꢀandꢀmakingꢀsureꢀthatꢀtheꢀtweeterꢀandꢀ  
wooferꢀwiresꢀcorrespondꢀtoꢀtheꢀcorrectꢀterminalsꢀ  
onꢀbothꢀtheꢀspeakerꢀandꢀtheꢀcrossover.ꢀ  
-or-  
Secureꢀtheꢀspeakerꢀandꢀspacerꢀgasketꢀ(ifꢀapplicable)ꢀ  
toꢀtheꢀpanelꢀbyꢀevenlyꢀtighteningꢀbyꢀhandꢀtheꢀ  
providedꢀ#8ꢀxꢀ1.25ꢀinchꢀ(32ꢀmm)ꢀmountingꢀscrews.ꢀ  
-or-  
WARNING  
!!  
Hand-tighten the screws evenly in a criss-cross  
pattern to avoid bending the speaker frame or  
stripping the mounting clips.  
11  
TweeTer InsTallaTIon  
First,ꢀrunꢀspeakerꢀwiresꢀfromꢀtheꢀtweeterꢀoutputꢀ  
ofꢀtheꢀcrossoverꢀ(seeꢀWiringꢀDiagramꢀBꢀonꢀpageꢀ5)ꢀ  
toꢀtheꢀdesiredꢀtweeterꢀmountingꢀlocations,ꢀobservingꢀ  
theꢀsameꢀprecautionsꢀasꢀmentionedꢀinꢀtheꢀwooferꢀ  
installationꢀsection.ꢀTerminateꢀtheꢀwiresꢀwithꢀtheꢀ  
suppliedꢀ2.8ꢀmmꢀmaleꢀcrimpableꢀconnectors.  
surface-mount Installation  
Inꢀthisꢀapplication,ꢀyouꢀwillꢀnotꢀneedꢀtoꢀcutꢀ  
largeꢀholesꢀinꢀyourꢀvehicle’sꢀpanelsꢀforꢀtheꢀtweeters.ꢀ  
Youꢀwillꢀonlyꢀneedꢀtoꢀdrillꢀaꢀholeꢀforꢀtheꢀwiresꢀandꢀ  
twoꢀsmallerꢀholesꢀforꢀtheꢀmountingꢀscrews.ꢀThisꢀ  
applicationꢀisꢀusefulꢀwhenꢀmountingꢀtheꢀtweetersꢀtoꢀ  
aꢀpanelꢀthatꢀhasꢀinsufficientꢀclearanceꢀbehindꢀitꢀforꢀ  
theꢀtweeter’sꢀmagnetꢀstructure.  
TweeTer FIXTure InsTallaTIon:  
Theꢀdomeꢀtweetersꢀsuppliedꢀwithꢀyourꢀꢀ  
Usingꢀtheꢀfixtureꢀasꢀaꢀtemplate,ꢀmarkꢀtheꢀscrewꢀ  
holeꢀlocationsꢀandꢀaꢀlocationꢀinꢀtheꢀcenterꢀofꢀtheꢀ  
fixtureꢀforꢀtheꢀwireꢀhole.ꢀRemoveꢀtheꢀfixtureꢀandꢀ  
drillꢀpilotꢀholesꢀforꢀtheꢀscrewsꢀandꢀaꢀ1/4-inchꢀ(6.4ꢀ  
mm)ꢀforꢀtheꢀwires.ꢀUseꢀtheꢀsuppliedꢀ#6ꢀxꢀ1.00-inchꢀ  
sheetꢀmetalꢀscrewsꢀtoꢀsecureꢀtheꢀfixtureꢀasꢀshownꢀinꢀ  
DiagramꢀK.ꢀNext,ꢀrouteꢀtheꢀtweeter’sꢀpositiveꢀ(+)ꢀandꢀ  
negativeꢀ(-)ꢀwireꢀleadsꢀthroughꢀtheꢀ1/4-inchꢀcenterꢀ  
hole.ꢀTheꢀtweeterꢀisꢀsecuredꢀtoꢀtheꢀfixtureꢀusingꢀaꢀ  
simpleꢀbayonetꢀ(twistꢀandꢀlock)ꢀmechanism.ꢀToꢀattachꢀ  
theꢀtweeterꢀtoꢀtheꢀsurface-mountꢀfixture,ꢀobserveꢀtheꢀ  
indentedꢀlockingꢀslotsꢀonꢀtheꢀouterꢀedgeꢀofꢀtheꢀtweeterꢀ  
bodyꢀandꢀalignꢀtheseꢀwithꢀtheꢀtabsꢀvisibleꢀonꢀtheꢀ  
insideꢀwallsꢀofꢀtheꢀfixture.ꢀTheꢀtweeterꢀshouldꢀslideꢀ  
intoꢀplaceꢀeasilyꢀandꢀcanꢀthenꢀbeꢀlockedꢀbyꢀpushingꢀ  
downꢀonꢀtheꢀtweeterꢀandꢀgivingꢀitꢀaꢀsmallꢀclockwiseꢀ  
turnꢀ(SeeꢀDiagramꢀK).  
C3-570ꢀsystemꢀhaveꢀbeenꢀdesignedꢀforꢀmaximumꢀ  
mountingꢀversatilityꢀinꢀaꢀcomponentꢀconfiguration.ꢀ  
Thereꢀareꢀtwoꢀprimaryꢀmethodsꢀbyꢀwhichꢀtheꢀ  
tweetersꢀcanꢀbeꢀmountedꢀinꢀyourꢀvehicle:  
Flush-mount Installation  
Theꢀdomeꢀtweetersꢀsuppliedꢀwithꢀyourꢀꢀ  
C3-570ꢀsystemꢀhaveꢀbeenꢀdesignedꢀtoꢀintegrateꢀwithꢀ  
yourꢀinstallationꢀinꢀaꢀclean,ꢀunobtrusiveꢀmannerꢀ  
usingꢀaꢀflush-mountꢀcup.ꢀThisꢀcompactꢀmountingꢀ  
fixtureꢀisꢀinstalledꢀusingꢀtheꢀmethodꢀillustratedꢀ  
inꢀDiagramꢀJꢀandꢀrequiresꢀaꢀmountingꢀholeꢀwithꢀaꢀ  
diameterꢀofꢀ1.875ꢀin.ꢀ(47.6ꢀmm).ꢀ  
Atꢀleastꢀ1.70-inchꢀ(43.2ꢀmm)ꢀofꢀclearanceꢀisꢀ  
requiredꢀbehindꢀtheꢀmountingꢀsurfaceꢀofꢀtheꢀtweeterꢀ  
forꢀtheꢀspringꢀclipsꢀandꢀ1-inchꢀmachineꢀscrewsꢀ  
usedꢀinꢀmountingꢀtheꢀfixture.ꢀInꢀlimitedꢀdepthꢀ  
applications,ꢀitꢀmayꢀbeꢀnecessaryꢀtoꢀcutꢀdownꢀtheꢀ  
lengthꢀofꢀtheꢀmachineꢀscrew,ꢀorꢀtoꢀuseꢀaꢀshorterꢀscrewꢀ  
(notꢀsupplied).ꢀHand-tightenꢀtheꢀmachineꢀscrewꢀuntilꢀ  
theꢀfixtureꢀisꢀsecureꢀ(SeeꢀDiagramꢀJ).  
12 | JL Audio - C3-570 Owner’s Manual  
DIaGram J: Flush-mount Tweeter Installation  
DIaGram K: surface-mount Tweeter Installation  
13  
noTes  
14 | JL Audio - C3-570 Owner’s Manual  
noTes  
15  
lImITeD warranTY - auTomoTIVe sPeaKer sYsTems (usa)  
JLꢀAUDIOꢀwarrantsꢀtheseꢀspeakersꢀ(andꢀcrossoverꢀnetworks,ꢀwhereꢀapplicable)ꢀtoꢀbeꢀfreeꢀofꢀdefectsꢀinꢀ  
materialsꢀandꢀworkmanshipꢀforꢀaꢀperiodꢀofꢀone (1) year.  
Thisꢀwarrantyꢀisꢀnotꢀtransferableꢀandꢀappliesꢀonlyꢀtoꢀtheꢀoriginalꢀpurchaserꢀfromꢀanꢀauthorizedꢀꢀ  
JLꢀAUDIOꢀdealer.ꢀꢀShouldꢀserviceꢀbeꢀnecessaryꢀunderꢀthisꢀwarrantyꢀforꢀanyꢀreasonꢀdueꢀtoꢀmanufacturingꢀ  
defectꢀorꢀmalfunction,ꢀJLꢀAUDIOꢀwillꢀ(atꢀitsꢀdiscretion),ꢀrepairꢀorꢀreplaceꢀtheꢀdefectiveꢀproductꢀwithꢀnewꢀorꢀ  
remanufacturedꢀproductꢀatꢀnoꢀcharge.ꢀDamageꢀcausedꢀbyꢀtheꢀfollowingꢀisꢀnotꢀcoveredꢀunderꢀwarranty:ꢀaccident,ꢀ  
misuse,ꢀabuse,ꢀproductꢀmodificationꢀorꢀneglect,ꢀfailureꢀtoꢀfollowꢀinstallationꢀinstructions,ꢀunauthorizedꢀrepairꢀ  
attempts,ꢀmisrepresentationsꢀbyꢀtheꢀseller.ꢀꢀThisꢀwarrantyꢀdoesꢀnotꢀcoverꢀincidentalꢀorꢀconsequentialꢀdamagesꢀ  
andꢀdoesꢀnotꢀcoverꢀtheꢀcostꢀofꢀremovingꢀorꢀreinstallingꢀtheꢀunit(s).ꢀꢀCosmeticꢀdamageꢀdueꢀtoꢀaccidentꢀorꢀnormalꢀ  
wearꢀandꢀtearꢀisꢀnotꢀcoveredꢀunderꢀwarranty.  
Anyꢀapplicableꢀimpliedꢀwarrantiesꢀareꢀlimitedꢀinꢀdurationꢀtoꢀtheꢀperiodꢀofꢀtheꢀexpressꢀwarrantyꢀasꢀprovidedꢀ  
hereinꢀbeginningꢀwithꢀtheꢀdateꢀofꢀtheꢀoriginalꢀpurchaseꢀatꢀretail,ꢀandꢀnoꢀwarranties,ꢀwhetherꢀexpressꢀorꢀimplied,ꢀ  
shallꢀapplyꢀtoꢀthisꢀproductꢀthereafter.ꢀꢀSomeꢀstatesꢀdoꢀnotꢀallowꢀlimitationsꢀonꢀimpliedꢀwarranties,ꢀthereforeꢀ  
theseꢀexclusionsꢀmayꢀnotꢀapplyꢀtoꢀyou.ꢀꢀThisꢀwarrantyꢀgivesꢀyouꢀspecificꢀlegalꢀrights,ꢀandꢀyouꢀmayꢀalsoꢀhaveꢀotherꢀ  
rightsꢀwhichꢀvaryꢀfromꢀstateꢀtoꢀstate.  
If you need service on your Jl auDIo product:  
AllꢀwarrantyꢀreturnsꢀshouldꢀbeꢀsentꢀtoꢀJLꢀAUDIOꢀfreightꢀprepaidꢀthroughꢀanꢀauthorizedꢀJLꢀAUDIOꢀ  
dealerꢀandꢀmustꢀbeꢀaccompaniedꢀbyꢀproofꢀofꢀpurchaseꢀ(aꢀcopyꢀofꢀtheꢀoriginalꢀsalesꢀreceipt.)ꢀꢀDirectꢀ  
returnsꢀfromꢀconsumersꢀorꢀnon-authorizedꢀdealersꢀwillꢀbeꢀrefusedꢀunlessꢀspecificallyꢀauthorizedꢀbyꢀ  
JLꢀAUDIOꢀwithꢀaꢀvalidꢀreturnꢀauthorizationꢀnumber.ꢀꢀWarrantyꢀexpirationꢀonꢀproductsꢀreturnedꢀ  
withoutꢀproofꢀofꢀpurchaseꢀwillꢀbeꢀdeterminedꢀfromꢀtheꢀmanufacturingꢀdateꢀcode.ꢀCoverageꢀmayꢀbeꢀ  
invalidatedꢀasꢀthisꢀdateꢀisꢀpreviousꢀtoꢀpurchaseꢀdate.ꢀꢀReturnꢀonlyꢀdefectiveꢀcomponents.ꢀꢀIfꢀoneꢀspeakerꢀ  
failsꢀinꢀaꢀsystem,ꢀreturnꢀonlyꢀthatꢀspeakerꢀcomponent,ꢀnotꢀtheꢀentireꢀsystem.ꢀNon-defectiveꢀitemsꢀ  
receivedꢀwillꢀbeꢀreturnedꢀfreight-collect.ꢀꢀCustomerꢀisꢀresponsibleꢀforꢀshippingꢀchargesꢀandꢀinsuranceꢀ  
inꢀsendingꢀtheꢀproductꢀtoꢀJLꢀAUDIO.ꢀꢀFreightꢀdamageꢀonꢀreturnsꢀisꢀnotꢀcoveredꢀunderꢀwarranty.ꢀ  
For service Information in the u.s.a. please call  
Jl audio Customer service: (954) 443-1100  
9:00 AM – 5:30 PM (Eastern Time Zone)  
Jl audio, Inc  
10369 North Commerce Pkwy.  
Miramar, FL 33025  
(do not send product for repair to this address)  
International warranties:  
Products purchased outside the United States of America are covered only  
by that country’s distributor and not by JL Audio, Inc.  
Printed in China  
C3-570-031010  

AudioBahn Natural Sound Subwoofer AW831T User Manual
Black Decker CRUSH MASTER BL14501P User Manual
Bunn O MATIC ULTRA 1 User Manual
Canon PowerShot A95 User Manual
Clarion APA2001 User Manual
Focal 6 KRXS User Manual
FujiFilm 600009286 User Manual
FujiFilm Digital Camera F750EXR User Manual
JVC CH X1500 User Manual
JVC EXAD LVT1373 001A User Manual